USA
Fusion3 F410 at a glance
The Fusion3 F410 is a 3D printer by Fusion3 with a 355 x 355 x 310 mm build volume.
- Build volume
- 355 x 355 x 310 mm
- Enclosure
- Fully enclosed
- Max print speed
- 250 mm/s
- Prints well
- PLA, PETG, ABS & ASA, Nylon (PA), Polycarbonate (PC)
- Connectivity
- Ethernet, SD card
Connect the Fusion3 F410 to SimplyPrint
Does the Fusion3 F410 3D printer work with SimplyPrint, OctoPrint, Mainsail and Fluidd? Each way of connecting it, what it needs, and how to set it up.
-
OctoPrint
Directly, over USB
Compatible
What you need: A Raspberry Pi running OctoPrint, plugged into the printer with a USB cable
-
Klipper (Moonraker)
Not compatible
- Doesn't ship with Klipper: it runs Klipper after you install it in place of its own firmware, a modification
What works with SimplyPrint
Connected through OctoPrint, SimplyPrint supports everything the Fusion3 F410 lets other software do: the camera and AI failure detection, remote printing, temperature and movement control and AutoPrint. 3 features depend on how it's set up: the table says what each needs.
Every SimplyPrint feature, for each way of connecting it to SimplyPrint
| Connected to SimplyPrint through | |
|---|---|
| SimplyPrint feature | OctoPrint Compatible |
| Monitoring | |
| Live status and progress | Yes |
| Webcam | Yes 1 |
| AI failure detection | Yes 1 |
| Time left | Yes |
| Layer progress | Yes |
| Temperatures | Yes |
| Printing | |
| Starting a print | Yes |
| Pause, resume and cancel | Yes |
| Skip objects | Depends 2 |
| Files | |
| Print binary G-code (.bgcode) | Depends 3 |
| Printer control | |
| Change temperatures | Yes |
| Moving with the controls | Yes |
| Homing | Yes |
| Extrude and retract | Yes |
| Change print speed | Yes |
| Fan speed | Yes |
| Baby stepping | Yes |
| Send G-code | Yes |
| Calibration | |
| Change filament | Yes |
| Bed leveling | Yes |
| Z-Offset Calibration | Yes |
| Automation | |
| AutoPrint Pro | Yes |
| Download the file before the print starts | Depends 4 |
Connected to SimplyPrint through OctoPrint
Compatible
Monitoring
- Live status and progress Yes
- Webcam Yes 1
- AI failure detection Yes 1
- Time left Yes
- Layer progress Yes
- Temperatures Yes
Printing
- Starting a print Yes
- Pause, resume and cancel Yes
- Skip objects Depends 2
Files
- Print binary G-code (.bgcode) Depends 3
Printer control
- Change temperatures Yes
- Moving with the controls Yes
- Homing Yes
- Extrude and retract Yes
- Change print speed Yes
- Fan speed Yes
- Baby stepping Yes
- Send G-code Yes
Calibration
- Change filament Yes
- Bed leveling Yes
- Z-Offset Calibration Yes
Automation
- AutoPrint Pro Yes
- Download the file before the print starts Depends 4
Works Depends Not supported
- Needs a camera
- Requires the OctoPrint plugin Cancel Objects
- Requires the OctoPrint plugin BGCode
- Requires version 4.2.0 or newer of the SimplyPrint plugin
What slicer to use for the Fusion3 F410
None of the slicers in SimplyPrint's cloud has a ready-made profile for the Fusion3 F410, but it takes standard G-code: start from a similar printer's profile and set the bed size, height and nozzle to match.
No profile for the Fusion3 F410
PrusaSlicer
OrcaSlicer
BambuStudio
ElegooSlicer
CrealityPrint
Cura
Kiri:MotoWe only list slicers you can use in the SimplyPrint cloud, so there may be others for the Fusion3 F410.
Cloud-Based Slicer for Fusion3 F410
All supported slicers - directly in your browser with SimplyPrint's online cloud slicer. No installation required. Slice your Fusion3 F410 models from any device, anywhere in the world!
Try Online Slicer NowProfiles and other slicers
Automatic Profile Updates: Profiles are automatically checked and fetched from the slicer GitHub repositories every day, as well as from our own open-source community-driven slicer profile database. This ensures you always have access to the latest profiles.
Note: Other slicers, such as Simplify3D, ideaMaker, SuperSlicer and KISSlicer, aren't in our cloud, so we don't track their profiles. They may still work well with your Fusion3 F410: check the slicer's own documentation or forums for a profile. You can also contribute profiles to our open-source slicer profile database on GitHub.
The app for the Fusion3 F410
SimplyPrint works as the Fusion3 F410's app: on your phone and in any browser, with a slicer in the cloud.
What you get with SimplyPrint
- An app for iPhone and Android, the same in any browser, and a slicer in the cloud.
- More than monitoring: a print queue, AI failure detection, AutoPrint and accounts for a team.
- Printers from many brands in one place, side by side.
- A European cloud: hosted in Frankfurt, Germany, under the GDPR.
Automate the Fusion3 F410
There's no plate swapper or auto-ejection kit for the Fusion3 F410 in SimplyPrint yet, but AutoPrint can still keep it printing: once the plate is clear, it starts the next job from your queue.
Ways to automate it
- Your own ejection G-code Write the routine that clears your plate, and AutoPrint runs it after every print.
- A robot arm, or anything with an API Tell SimplyPrint the plate is clear through the API or a webhook, from a robot arm or your own system.
- Clear it by hand, keep the queue AutoPrint waits for you to mark the plate clear, then starts the next job.
AutoPrint comes with the Pro plan and up.
Fusion3 F410 specifications: bed size, print height and more
Its size, temperatures, multi-material and how it connects, from the maker and our own research. Read more by the manufacturer
Size
| Build volume | 355 x 355 x 310 mm |
|---|---|
| Bed type | Square |
| Bed size | 355 x 355 mm |
| Max print height | 310 mm |
Printing
| Enclosure | Fully enclosed |
|---|---|
| Max print speed | 250 mm/s |
| Max extruder temperature | 300 °C |
| Has heated bed | Yes |
| Max bed temperature | 140 °C |
| Number of nozzles | 1 |
| Toolheads | 1 |
| Direct drive | No |
| Probing tool / Auto Bed Leveling | Yes |
| Filament width | 1.75 mm |
Multi-material
| Toolchanger or hotend changer | No |
|---|---|
| IDEX (independent dual extruders) | No |
Connecting
| Connectivity | Ethernet, SD card |
|---|---|
| Supports serial printing | Yes |
| Shipped firmware | Marlin |
Files and slicing
| Supported file formats | G-code (.gcode, .gco, .g) |
|---|
The printer
| Printer manufacturer / brand | Fusion3 |
|---|---|
| Printer model name | F410 |
| Made by a company from | USA |
| Launched | 2018 |
| Still made | No, discontinued |
Disclaimer: We strive to keep this information as current and accurate as possible, but cannot guarantee its completeness or reliability. Our data is based on user submissions and manufacturer references.
What filament can the Fusion3 F410 print?
Filament compatibility for the Fusion3 F410: the materials it can handle, judged from its hotend, bed, chamber and enclosure.
| Filament | Suitability | Notes |
|---|---|---|
| PLA | Great | The easiest filament to print. Works on almost any printer; a heated bed helps adhesion but is not required. |
| PETG | Great | Comfortably in range (PETG likes a ~230-250C hotend and a ~70-85C bed). |
| TPU & flexibles | With care | Possible, but a Bowden extruder makes flexibles harder - print slowly and prefer firmer (higher-shore) TPU. |
| ABS & ASA | Great | Enclosed, with a hot enough hotend and bed: ABS and ASA print well. |
| Nylon (PA) | Good | Doable with care - dry the filament thoroughly, and an enclosure helps a lot. |
| Polycarbonate (PC) | Good | In range for PC. Dry the filament, print slowly, and use an enclosure for the best results. |
| Carbon-fiber & glass-filled | With care | Possible if you fit a hardened or wear-resistant nozzle - the abrasive fibers quickly wear a stock brass nozzle. |
Tip: this is a general guide from the printer's specs - always check your filament's recommended settings. With SimplyPrint you can save a profile for each spool and track exactly what filament you have in stock.
Best filament for the Fusion3 F410
Filaments the Fusion3 F410 prints well, Fusion3's own first, then the best known.
Compare the Fusion3 F410 with similar printers
Printers from the same maker, of a similar size, printing the same engineering materials or multi-material like it, that you can buy today. Compare up to four side by side, with their specs and how each connects.
-
Fusion3 EDGE
368 x 368 x 343 mmLaunched 2022Connects with: OctoPrintAlso by Fusion3 · Similar build volume · Also prints ABS & ASA, Nylon (PA), Polycarbonate (PC)Compatible Compare side by side Fusion3 EDGE -
Creality K1 Max
300 x 300 x 300 mmLaunched July 14, 2023Connects with: SimplyPrint Client, Klipper (Moonraker)Similar build volume · Also prints ABS & ASA, Nylon (PA), Polycarbonate (PC)Compatible Compare side by side Creality K1 Max -
Bambu Lab H2S Combo
340 x 320 x 340 mmLaunched August 26, 2025Connects with: SimplyPrint ClientSimilar build volume · Also prints ABS & ASA, Nylon (PA), Polycarbonate (PC)Verified by SimplyPrint Compare side by side Bambu Lab H2S Combo -
Bambu Lab H2D Combo
325 x 320 x 325 mmLaunched March 25, 2025Connects with: SimplyPrint ClientSimilar build volume · Also prints ABS & ASA, Nylon (PA), Polycarbonate (PC)Verified by SimplyPrint Compare side by side Bambu Lab H2D Combo
What to buy instead of the Fusion3 F410
Fusion3 no longer makes or sells the F410 new. These printers like it are on sale today, and work with SimplyPrint.
-
Creality K1 Max 300 x 300 x 300 mmSimilar build volume · Also prints ABS & ASA, Nylon (PA), Polycarbonate (PC)$549.00 Price at Creality Store, checked October 23, 2026Buy from Creality Affiliate link
-
Bambu Lab H2S Combo 340 x 320 x 340 mmSimilar build volume · Also prints ABS & ASA, Nylon (PA), Polycarbonate (PC)
-
Bambu Lab H2D Combo 325 x 320 x 325 mmSimilar build volume · Also prints ABS & ASA, Nylon (PA), Polycarbonate (PC)
Frequently asked questions
Is the Fusion3 F410 compatible with SimplyPrint?
Yes. You can connect the Fusion3 F410 to SimplyPrint via OctoPrint, then slice, queue, start and monitor prints from your browser or the mobile app.
How do I connect the Fusion3 F410 to SimplyPrint?
Follow our step-by-step setup guide for the Fusion3 F410. It shows how to connect it via OctoPrint, what you need for each, and which to pick.
What slicer should I use for the Fusion3 F410?
Cura, PrusaSlicer and OrcaSlicer all work with the Fusion3 F410, and you can run any of them in SimplyPrint's online browser slicer - no install needed, on any device.
Can I use OrcaSlicer with the Fusion3 F410?
Yes, but OrcaSlicer has no built-in profile for the Fusion3 F410 that we know of: start from a similar printer's profile and set the bed size, height and nozzle to match.
What filament can the Fusion3 F410 print?
Based on its specs (hotend up to 300C, heated bed up to 140C), the Fusion3 F410 handles PLA, PETG, ABS & ASA, or Nylon (PA) well. See the full filament guide above for ABS, nylon, PC and composites.
Does the Fusion3 F410 work with OctoPrint or Klipper?
The Fusion3 F410 works with OctoPrint, and SimplyPrint connects to it through them - so you get cloud access, a queue and camera monitoring on top.
What is the Fusion3 F410's bed size and build volume?
The Fusion3 F410 has a 355 x 355 mm print bed and prints up to 310 mm tall, a build volume of about 355 x 355 x 310 mm. See the full specifications table above for bed type, temperatures and more.
When did the Fusion3 F410 come out?
Fusion3 launched the F410 in 2018. It has since been discontinued, so you can't buy it new from Fusion3 any more.
Can the Fusion3 F410 eject prints automatically?
There's no kit for it that we support yet, but SimplyPrint's AutoPrint can run your own ejection G-code, work with a robot arm through the API, or wait for you to clear the plate, and then start the next job from your queue.
Is the Fusion3 F410 still sold?
No. Fusion3 no longer makes or sells the F410 new. Printers like it you can buy today: Creality K1 Max, Bambu Lab H2S Combo and Bambu Lab H2D Combo.
Affiliate disclosure: Some links on this page are affiliate links. We may earn a commission if you make a purchase, at no extra cost to you. As an Amazon Associate, we earn from qualifying purchases.
© 2026 SimplyPrint. All rights reserved. This page and the compatibility, specification and review data on it are compiled by SimplyPrint and may not be copied, scraped, reproduced or republished, in whole or in part, without prior written permission. Printer images are the property of their respective manufacturers and are shown for identification purposes only; SimplyPrint claims no ownership of them. Quoted reviews belong to their authors.