Raise3D N2 Plus: specs, SimplyPrint compatibility and setup

By Raise3D, China Launched 2016

Does it work with SimplyPrint?

Not confirmed yet - help us find out We can't tell

We don't know yet. If you have one, you can find out in a few minutes and confirm it for everyone.

Find out if it works

Raise3D N2 Plus at a glance

The Raise3D N2 Plus is a 3D printer by Raise3D with a 305 x 305 x 610 mm build volume.

Build volume
305 x 305 x 610 mm
Enclosure
Fully enclosed
Max print speed
150 mm/s
Motion system
Other kinematics
Prints well
PLA, PETG, TPU & flexibles, ABS & ASA, Nylon (PA), Polycarbonate (PC), Carbon-fiber & glass-filled
Built-in camera
No
Connectivity
Ethernet, Wi-Fi, USB, SD card
All specifications

Connect the Raise3D N2 Plus to SimplyPrint

Does the Raise3D N2 Plus 3D printer work with SimplyPrint, OctoPrint, Mainsail and Fluidd? Each way of connecting it, what it needs, and how to set it up.

  • SimplyPrint

    SimplyPrint

    Not confirmed yet - help us find out

    Help us confirm Be one of the first to confirm it
  • OctoPrint

    OctoPrint

    Directly, over USB

    Not confirmed yet - help us find out

    Likely but unconfirmed: Raise3D's published N-series firmware is Marlin on a RUMBA board at 230400 baud, which normally prints over USB serial. No source shows OctoPrint driving an N2 Plus, and later units route through the Raise Touch screen. Source

    Help us confirm Be one of the first to confirm it
  • Mainsail Fluidd

    Klipper (Moonraker)

    Not compatible

    Ships Raise3D's Marlin fork; Klipper only after you install it. Source

    • Doesn't ship with Klipper: it runs Klipper after you install it in place of its own firmware, a modification

What slicer to use for the Raise3D N2 Plus

None of the slicers in SimplyPrint's cloud has a ready-made profile for the Raise3D N2 Plus, but it takes standard G-code: start from a similar printer's profile and set the bed size, height and nozzle to match.

Raise3D's own slicer

  • ideaMaker
    Made by Raise3D, not in the SimplyPrint cloud

No profile for the Raise3D N2 Plus

We only list slicers you can use in the SimplyPrint cloud, so there may be others for the Raise3D N2 Plus.

Cloud-Based Slicer for Raise3D N2 Plus

All supported slicers - directly in your browser with SimplyPrint's online cloud slicer. No installation required. Slice your Raise3D N2 Plus models from any device, anywhere in the world!

Try Online Slicer Now
Profiles and other slicers

Automatic Profile Updates: Profiles are automatically checked and fetched from the slicer GitHub repositories every day, as well as from our own open-source community-driven slicer profile database. This ensures you always have access to the latest profiles.

Note: Other slicers, such as Simplify3D, ideaMaker, SuperSlicer and KISSlicer, aren't in our cloud, so we don't track their profiles. They may still work well with your Raise3D N2 Plus: check the slicer's own documentation or forums for a profile. You can also contribute profiles to our open-source slicer profile database on GitHub.

The app for the Raise3D N2 Plus

Raise3D's own app is RaiseCloud.

Raise3D N2 Plus specifications: bed size, print height and more

Its size, temperatures, multi-material and how it connects, from the maker and our own research. Read more by the manufacturer

Size

Build volume 305 x 305 x 610 mm
Bed type Square
Bed size 305 x 305 mm
Max print height 610 mm

Printing

Enclosure Fully enclosed
Motion system Other kinematics
Max print speed 150 mm/s
Max extruder temperature 300 °C
Has heated bed Yes
Max bed temperature 110 °C
Number of nozzles 1
Direct drive Yes
Probing tool / Auto Bed Leveling No
Filament width 1.75 mm

Connecting

Connectivity Ethernet, Wi-Fi, USB, SD card
Built-in camera No
Prints from USB stick, SD card
Supports serial printing Unknown
Shipped firmware Marlin

Files and slicing

Supported file formats G-code (.gcode, .gco, .g)

The printer

Printer manufacturer / brand Raise3D
Printer model name N2 Plus
Made by a company from China
Launched 2016

Disclaimer: We strive to keep this information as current and accurate as possible, but cannot guarantee its completeness or reliability. Our data is based on user submissions and manufacturer references.

What filament can the Raise3D N2 Plus print?

Filament compatibility for the Raise3D N2 Plus: the materials Raise3D lists for it.

Filament Suitability Notes
PLA Great On the maker's list of materials for this printer.
PETG Great On the maker's list of materials for this printer.
TPU & flexibles Great On the maker's list of materials for this printer.
ABS & ASA Great On the maker's list of materials for this printer.
Nylon (PA) Good Doable with care - dry the filament thoroughly, and an enclosure helps a lot.
Polycarbonate (PC) Great On the maker's list of materials for this printer.
Carbon-fiber & glass-filled Great On the maker's list of materials for this printer.

Tip: this is a general guide from the printer's specs - always check your filament's recommended settings. With SimplyPrint you can save a profile for each spool and track exactly what filament you have in stock.

Printers like the Raise3D N2 Plus that work with SimplyPrint

Printers from the same maker, of a similar size, printing the same engineering materials or multi-material like it, that you can buy today and that we know work with SimplyPrint.

  • Bambu Lab H2S Combo 3D printer
    Bambu Lab H2S Combo
    340 x 320 x 340 mm
    Launched August 26, 2025
    Connects with: SimplyPrint Client
    Similar build volume · Also prints ABS & ASA, Nylon (PA), Polycarbonate (PC), Carbon-fiber & glass-filled
    Verified by SimplyPrint
  • Creality K2 Plus Combo 3D printer
    Creality K2 Plus Combo
    350 x 350 x 350 mm
    Launched July 31, 2024
    Connects with: SimplyPrint Client, Klipper (Moonraker)
    Similar build volume · Also prints ABS & ASA, Nylon (PA), Polycarbonate (PC)
    Compatible
  • FLSUN S1 3D printer
    FLSUN S1
    320 x 320 x 430 mm
    Launched June 3, 2024
    Connects with: Klipper (Moonraker)
    Similar build volume · Also prints ABS & ASA, Nylon (PA), Polycarbonate (PC)
    Compatible
  • Vivedino Troodon 2.0 3D printer
    Vivedino Troodon 2.0
    350 x 350 x 320 mm
    Launched 2022
    Connects with: OctoPrint
    Similar build volume · Also prints ABS & ASA, Nylon (PA), Polycarbonate (PC)
    Compatible
Compare 3D printers that work with SimplyPrint All Raise3D printers

Frequently asked questions

Is the Raise3D N2 Plus compatible with SimplyPrint?

We don't know yet. SimplyPrint works with 130+ brands and 600+ models via OctoPrint, Klipper and built-in integrations; if you have a Raise3D N2 Plus, our compatibility check tells you in a few questions how it could connect.

What slicer should I use for the Raise3D N2 Plus?

Cura, PrusaSlicer and OrcaSlicer all work with the Raise3D N2 Plus, and you can run any of them in SimplyPrint's online browser slicer - no install needed, on any device.

Can I use OrcaSlicer with the Raise3D N2 Plus?

Yes, but OrcaSlicer has no built-in profile for the Raise3D N2 Plus that we know of: start from a similar printer's profile and set the bed size, height and nozzle to match.

What filament can the Raise3D N2 Plus print?

Raise3D lists PLA, PETG, TPU & flexibles, ABS & ASA, Polycarbonate (PC) and Carbon-fiber & glass-filled for the N2 Plus.

What is the Raise3D N2 Plus's bed size and build volume?

The Raise3D N2 Plus has a 305 x 305 mm print bed and prints up to 610 mm tall, a build volume of about 305 x 305 x 610 mm. See the full specifications table above for bed type, temperatures and more.

When did the Raise3D N2 Plus come out?

Raise3D launched the N2 Plus in 2016.

© 2026 SimplyPrint. All rights reserved. This page and the compatibility, specification and review data on it are compiled by SimplyPrint and may not be copied, scraped, reproduced or republished, in whole or in part, without prior written permission. Printer images are the property of their respective manufacturers and are shown for identification purposes only; SimplyPrint claims no ownership of them. Quoted reviews belong to their authors.