Canada
Tinkerine Ditto Pro at a glance
The Tinkerine Ditto Pro is a 3D printer by Tinkerine with a 215 x 165 x 220 mm build volume.
- Build volume
- 215 x 165 x 220 mm
- Enclosure
- Open frame
- Prints well
- PLA
- Connectivity
- SD card
Connect the Tinkerine Ditto Pro to SimplyPrint
Does the Tinkerine Ditto Pro 3D printer work with SimplyPrint, OctoPrint, Mainsail and Fluidd? Each way of connecting it, what it needs, and how to set it up.
-
OctoPrint
Directly, over USB
Compatible
What you need: A Raspberry Pi running OctoPrint, plugged into the printer with a USB cable
-
Klipper (Moonraker)
Not compatible
- Doesn't ship with Klipper: it runs Klipper after you install it in place of its own firmware, a modification
What works with SimplyPrint
Connected through OctoPrint, SimplyPrint supports everything the Tinkerine Ditto Pro lets other software do: the camera and AI failure detection, remote printing, temperature and movement control and AutoPrint. 3 features depend on how it's set up: the table says what each needs.
Every SimplyPrint feature, for each way of connecting it to SimplyPrint
| Connected to SimplyPrint through | |
|---|---|
| SimplyPrint feature | OctoPrint Compatible |
| Monitoring | |
| Live status and progress | Yes |
| Webcam | Yes 1 |
| AI failure detection | Yes 1 |
| Time left | Yes |
| Layer progress | Yes |
| Temperatures | Yes |
| Printing | |
| Starting a print | Yes |
| Pause, resume and cancel | Yes |
| Skip objects | Depends 2 |
| Files | |
| Print binary G-code (.bgcode) | Depends 3 |
| Printer control | |
| Change temperatures | Yes |
| Moving with the controls | Yes |
| Homing | Yes |
| Extrude and retract | Yes |
| Change print speed | Yes |
| Fan speed | Yes |
| Baby stepping | Yes |
| Send G-code | Yes |
| Calibration | |
| Change filament | Yes |
| Bed leveling | Yes |
| Z-Offset Calibration | Yes |
| Automation | |
| AutoPrint Pro | Yes |
| Download the file before the print starts | Depends 4 |
Connected to SimplyPrint through OctoPrint
Compatible
Monitoring
- Live status and progress Yes
- Webcam Yes 1
- AI failure detection Yes 1
- Time left Yes
- Layer progress Yes
- Temperatures Yes
Printing
- Starting a print Yes
- Pause, resume and cancel Yes
- Skip objects Depends 2
Files
- Print binary G-code (.bgcode) Depends 3
Printer control
- Change temperatures Yes
- Moving with the controls Yes
- Homing Yes
- Extrude and retract Yes
- Change print speed Yes
- Fan speed Yes
- Baby stepping Yes
- Send G-code Yes
Calibration
- Change filament Yes
- Bed leveling Yes
- Z-Offset Calibration Yes
Automation
- AutoPrint Pro Yes
- Download the file before the print starts Depends 4
Works Depends Not supported
- Needs a camera
- Requires the OctoPrint plugin Cancel Objects
- Requires the OctoPrint plugin BGCode
- Requires version 4.2.0 or newer of the SimplyPrint plugin
What slicer to use for the Tinkerine Ditto Pro
None of the slicers in SimplyPrint's cloud has a ready-made profile for the Tinkerine Ditto Pro, but it takes standard G-code: start from a similar printer's profile and set the bed size, height and nozzle to match.
No profile for the Tinkerine Ditto Pro
PrusaSlicer
OrcaSlicer
BambuStudio
ElegooSlicer
CrealityPrint
Cura
Kiri:MotoWe only list slicers you can use in the SimplyPrint cloud, so there may be others for the Tinkerine Ditto Pro.
Cloud-Based Slicer for Tinkerine Ditto Pro
All supported slicers - directly in your browser with SimplyPrint's online cloud slicer. No installation required. Slice your Tinkerine Ditto Pro models from any device, anywhere in the world!
Try Online Slicer NowProfiles and other slicers
Automatic Profile Updates: Profiles are automatically checked and fetched from the slicer GitHub repositories every day, as well as from our own open-source community-driven slicer profile database. This ensures you always have access to the latest profiles.
Note: Other slicers, such as Simplify3D, ideaMaker, SuperSlicer and KISSlicer, aren't in our cloud, so we don't track their profiles. They may still work well with your Tinkerine Ditto Pro: check the slicer's own documentation or forums for a profile. You can also contribute profiles to our open-source slicer profile database on GitHub.
The app for the Tinkerine Ditto Pro
SimplyPrint works as the Tinkerine Ditto Pro's app: on your phone and in any browser, with a slicer in the cloud.
What you get with SimplyPrint
- An app for iPhone and Android, the same in any browser, and a slicer in the cloud.
- More than monitoring: a print queue, AI failure detection, AutoPrint and accounts for a team.
- Printers from many brands in one place, side by side.
- A European cloud: hosted in Frankfurt, Germany, under the GDPR.
Automate the Tinkerine Ditto Pro
There's no plate swapper or auto-ejection kit for the Tinkerine Ditto Pro in SimplyPrint yet, but AutoPrint can still keep it printing: once the plate is clear, it starts the next job from your queue.
Ways to automate it
- Your own ejection G-code Write the routine that clears your plate, and AutoPrint runs it after every print.
- A robot arm, or anything with an API Tell SimplyPrint the plate is clear through the API or a webhook, from a robot arm or your own system.
- Clear it by hand, keep the queue AutoPrint waits for you to mark the plate clear, then starts the next job.
AutoPrint comes with the Pro plan and up.
Tinkerine Ditto Pro specifications: bed size, print height and more
Its size, temperatures, multi-material and how it connects, from the maker and our own research.
Size
| Build volume | 215 x 165 x 220 mm |
|---|---|
| Bed type | Rectangle |
| Bed size | 215 x 165 mm |
| Max print height | 220 mm |
Printing
| Enclosure | Open frame |
|---|---|
| Max extruder temperature | 280 °C |
| Has heated bed | No |
| Number of nozzles | 1 |
| Direct drive | No |
| Probing tool / Auto Bed Leveling | No |
| Filament width | 1.75 mm |
Connecting
| Connectivity | SD card |
|---|---|
| Prints from | SD card |
| Supports serial printing | Yes |
| Shipped firmware | Marlin |
Files and slicing
| Supported file formats | G-code (.gcode, .gco, .g) |
|---|
The printer
| Printer manufacturer / brand | Tinkerine |
|---|---|
| Printer model name | Ditto Pro |
| Made by a company from | Canada |
| Launched | May 1, 2014 |
Disclaimer: We strive to keep this information as current and accurate as possible, but cannot guarantee its completeness or reliability. Our data is based on user submissions and manufacturer references.
What filament can the Tinkerine Ditto Pro print?
Filament compatibility for the Tinkerine Ditto Pro: the materials it can handle, judged from its hotend, bed, chamber and enclosure.
| Filament | Suitability | Notes |
|---|---|---|
| PLA | Great | The easiest filament to print. Works on almost any printer; a heated bed helps adhesion but is not required. |
| PETG | With care | Marginal - PETG prefers a hotter bed (~70-80C) than this printer reaches. |
| TPU & flexibles | With care | Possible, but a Bowden extruder makes flexibles harder - print slowly and prefer firmer (higher-shore) TPU. |
| ABS & ASA | Not ideal | Not recommended - the bed cannot reach the ~90-110C ABS and ASA need. |
| Nylon (PA) | Not ideal | Not recommended - nylon needs a hotter hotend (~250-270C) and ideally an enclosure. |
| Polycarbonate (PC) | Not ideal | Not recommended - PC needs very high hotend temps and an enclosed chamber. |
| Carbon-fiber & glass-filled | With care | Possible if you fit a hardened or wear-resistant nozzle - the abrasive fibers quickly wear a stock brass nozzle. |
Tip: this is a general guide from the printer's specs - always check your filament's recommended settings. With SimplyPrint you can save a profile for each spool and track exactly what filament you have in stock.
Best filament for the Tinkerine Ditto Pro
Filaments the Tinkerine Ditto Pro prints well, Tinkerine's own first, then the best known.
Compare the Tinkerine Ditto Pro with similar printers
Printers from the same maker, of a similar size, printing the same engineering materials or multi-material like it, that you can buy today. Compare up to four side by side, with their specs and how each connects.
-
Tinkerine Ditto Pro R
215 x 165 x 220 mmConnects with: OctoPrintAlso by Tinkerine · Similar build volumeCompatible Compare side by side Tinkerine Ditto Pro R -
Bambu Lab A1 Mini
180 x 180 x 180 mmLaunched September 20, 2023Connects with: SimplyPrint ClientSimilar build volumeVerified by SimplyPrint Compare side by side Bambu Lab A1 Mini -
Creality Ender-3 V3 KE
220 x 220 x 240 mmLaunched September 15, 2023Connects with: SimplyPrint Client, Klipper (Moonraker)Similar build volumeCompatible Compare side by side Creality Ender-3 V3 KE -
Prusa MK4
250 x 210 x 220 mmLaunched March 29, 2023Connects with: SimplyPrint Client, OctoPrint, Prusa direct firmwareSimilar build volumeCompatible Compare side by side Prusa MK4
Frequently asked questions
Is the Tinkerine Ditto Pro compatible with SimplyPrint?
Yes. You can connect the Tinkerine Ditto Pro to SimplyPrint via OctoPrint, then slice, queue, start and monitor prints from your browser or the mobile app.
How do I connect the Tinkerine Ditto Pro to SimplyPrint?
Follow our step-by-step setup guide for the Tinkerine Ditto Pro. It shows how to connect it via OctoPrint, what you need for each, and which to pick.
What slicer should I use for the Tinkerine Ditto Pro?
Cura, PrusaSlicer and OrcaSlicer all work with the Tinkerine Ditto Pro, and you can run any of them in SimplyPrint's online browser slicer - no install needed, on any device.
Can I use OrcaSlicer with the Tinkerine Ditto Pro?
Yes, but OrcaSlicer has no built-in profile for the Tinkerine Ditto Pro that we know of: start from a similar printer's profile and set the bed size, height and nozzle to match.
What filament can the Tinkerine Ditto Pro print?
Based on its specs (hotend up to 280C, no heated bed), the Tinkerine Ditto Pro handles PLA well. See the full filament guide above for ABS, nylon, PC and composites.
Does the Tinkerine Ditto Pro work with OctoPrint or Klipper?
The Tinkerine Ditto Pro works with OctoPrint, and SimplyPrint connects to it through them - so you get cloud access, a queue and camera monitoring on top.
What is the Tinkerine Ditto Pro's bed size and build volume?
The Tinkerine Ditto Pro has a 215 x 165 mm print bed and prints up to 220 mm tall, a build volume of about 215 x 165 x 220 mm. See the full specifications table above for bed type, temperatures and more.
When did the Tinkerine Ditto Pro come out?
Tinkerine launched the Ditto Pro on May 1, 2014.
Can the Tinkerine Ditto Pro eject prints automatically?
There's no kit for it that we support yet, but SimplyPrint's AutoPrint can run your own ejection G-code, work with a robot arm through the API, or wait for you to clear the plate, and then start the next job from your queue.
Affiliate disclosure: Some links on this page are affiliate links. We may earn a commission if you make a purchase, at no extra cost to you. As an Amazon Associate, we earn from qualifying purchases.
© 2026 SimplyPrint. All rights reserved. This page and the compatibility, specification and review data on it are compiled by SimplyPrint and may not be copied, scraped, reproduced or republished, in whole or in part, without prior written permission. Printer images are the property of their respective manufacturers and are shown for identification purposes only; SimplyPrint claims no ownership of them. Quoted reviews belong to their authors.