Raise3D Pro2 Plus: specs, SimplyPrint compatibility and setup

By Raise3D, China Launched April 2018

Raise3D Pro2 Plus image

Does it work with SimplyPrint?

Not expected to work Most likely not

We don't expect it to work, but we could be wrong.

Find out if it works

Raise3D Pro2 Plus at a glance

The Raise3D Pro2 Plus is a 3D printer by Raise3D with a 305 x 305 x 605 mm build volume.

Build volume
305 x 305 x 605 mm
Enclosure
Fully enclosed
Max print speed
150 mm/s
Motion system
Other kinematics
Prints well
PLA, PETG, TPU & flexibles, ABS & ASA, Nylon (PA), Polycarbonate (PC), Carbon-fiber & glass-filled
Built-in camera
Yes
Connectivity
Wi-Fi, Ethernet, USB
All specifications

Connect the Raise3D Pro2 Plus to SimplyPrint

Does the Raise3D Pro2 Plus 3D printer work with SimplyPrint, OctoPrint, Mainsail and Fluidd? Each way of connecting it, what it needs, and how to set it up.

  • SimplyPrint

    SimplyPrint

    Not expected to work

    Find out how to check
  • Mainsail Fluidd

    Klipper (Moonraker)

    Not expected to work

    Ships Raise3D's firmware (ARM Cortex-M7 motion controller + i.MX6 embedded-Linux logic board); no Klipper or Moonraker. Source

    Find out how to check
  • OctoPrint

    OctoPrint

    Directly, over USB

    Not expected to work

    Spec sheet lists only USB 2.0 host ports and Ethernet on the logic board; the motion controller is driven internally. The catalog's Pro2 carries a legacy OctoPrint flag, but no source shows OctoPrint working. Source

    Find out how to check

No known way to connect it to SimplyPrint

Unfortunately, the Raise3D Pro2 Plus is currently not, to our knowledge, compatible with OctoPrint, Mainsail, Fluidd, or SimplyPrint. For the best 3D printing experience, consider other 3D printers that are compatible with these softwares.

How we determine compatibility

We consider a printer compatible if it works with one or more of the following:

  • SimplyPrint custom integration for this specific model
  • OctoPrint support (requires the printer to support serial printing)
  • Klipper support (printer can run Klipper, either by flashing compatible firmware or using an external controller/pad)

OctoPrint compatibility is primarily based on whether the printer supports serial communication. If serial printing is not supported, we mark OctoPrint as not compatible.

Note: Some printers have third-party OctoPrint plugins that enable unofficial/custom connections. We don’t maintain a list of these plugins, so they are not reflected in our compatibility data.

See printers that work View Compatible Printers

What slicer to use for the Raise3D Pro2 Plus

Use Raise3D's own slicer, ideaMaker: none of the slicers in SimplyPrint's cloud has a profile for the Raise3D Pro2 Plus, and it doesn't take standard G-code that we know of.

Raise3D's own slicer

  • ideaMaker
    Made by Raise3D, not in the SimplyPrint cloud

No profile for the Raise3D Pro2 Plus

We only list slicers you can use in the SimplyPrint cloud, so there may be others for the Raise3D Pro2 Plus.

No online slicing for the Raise3D Pro2 Plus

Get ideaMaker

The app for the Raise3D Pro2 Plus

Raise3D's own app is RaiseCloud.

Raise3D Pro2 Plus specifications: bed size, print height and more

Its size, temperatures, multi-material and how it connects, from the maker and our own research. Read more by the manufacturer

Size

Build volume 305 x 305 x 605 mm
Bed type Square
Bed size 305 x 305 mm
Max print height 605 mm

Printing

Enclosure Fully enclosed
Motion system Other kinematics
Max print speed 150 mm/s
Max extruder temperature 300 °C
Has heated bed Yes
Max bed temperature 110 °C
Number of nozzles 2
Toolheads 2
Direct drive Yes
Probing tool / Auto Bed Leveling No
Filament width 1.75 mm

Multi-material

Toolchanger or hotend changer No
IDEX (independent dual extruders) No

Connecting

Connectivity Wi-Fi, Ethernet, USB
Built-in camera Yes
Prints from USB stick
Supports serial printing No
Shipped firmware The maker's own

Files and slicing

Supported file formats G-code (.gcode, .gco, .g)

The printer

Printer manufacturer / brand Raise3D
Printer model name Pro2 Plus
Made by a company from China
Launched April 2018
Still made Yes

Disclaimer: We strive to keep this information as current and accurate as possible, but cannot guarantee its completeness or reliability. Our data is based on user submissions and manufacturer references.

What filament can the Raise3D Pro2 Plus print?

Filament compatibility for the Raise3D Pro2 Plus: the materials Raise3D lists for it.

Filament Suitability Notes
PLA Great On the maker's list of materials for this printer.
PETG Great On the maker's list of materials for this printer.
TPU & flexibles Great On the maker's list of materials for this printer.
ABS & ASA Great On the maker's list of materials for this printer.
Nylon (PA) Great On the maker's list of materials for this printer.
Polycarbonate (PC) Great On the maker's list of materials for this printer.
Carbon-fiber & glass-filled Great On the maker's list of materials for this printer.

Tip: this is a general guide from the printer's specs - always check your filament's recommended settings. With SimplyPrint you can save a profile for each spool and track exactly what filament you have in stock.

Printers like the Raise3D Pro2 Plus that work with SimplyPrint

Printers from the same maker, of a similar size, printing the same engineering materials or multi-material like it, that you can buy today and that we know work with SimplyPrint.

  • Bambu Lab H2S Combo 3D printer
    Bambu Lab H2S Combo
    340 x 320 x 340 mm
    Launched August 26, 2025
    Connects with: SimplyPrint Client
    Similar build volume · Also prints ABS & ASA, Nylon (PA), Polycarbonate (PC), Carbon-fiber & glass-filled
    Verified by SimplyPrint
  • Creality K2 Plus Combo 3D printer
    Creality K2 Plus Combo
    350 x 350 x 350 mm
    Launched July 31, 2024
    Connects with: SimplyPrint Client, Klipper (Moonraker)
    Similar build volume · Also prints ABS & ASA, Nylon (PA), Polycarbonate (PC)
    Compatible
  • FLSUN S1 3D printer
    FLSUN S1
    320 x 320 x 430 mm
    Launched June 3, 2024
    Connects with: Klipper (Moonraker)
    Similar build volume · Also prints ABS & ASA, Nylon (PA), Polycarbonate (PC)
    Compatible
  • Vivedino Troodon 2.0 3D printer
    Vivedino Troodon 2.0
    350 x 350 x 320 mm
    Launched 2022
    Connects with: OctoPrint
    Similar build volume · Also prints ABS & ASA, Nylon (PA), Polycarbonate (PC)
    Compatible
Compare 3D printers that work with SimplyPrint All Raise3D printers

Frequently asked questions

Is the Raise3D Pro2 Plus compatible with SimplyPrint?

To our knowledge the Raise3D Pro2 Plus is not yet supported. SimplyPrint works with 130+ brands and 600+ models via OctoPrint, Klipper and built-in integrations - check the compatibility list for a supported printer.

What slicer should I use for the Raise3D Pro2 Plus?

Use Raise3D's own slicer, ideaMaker: none of the slicers in SimplyPrint's cloud has a profile for the Raise3D Pro2 Plus, and it doesn't take standard G-code that we know of.

What filament can the Raise3D Pro2 Plus print?

Raise3D lists PLA, PETG, TPU & flexibles, ABS & ASA, Polycarbonate (PC), Nylon (PA) and Carbon-fiber & glass-filled for the Pro2 Plus.

What is the Raise3D Pro2 Plus's bed size and build volume?

The Raise3D Pro2 Plus has a 305 x 305 mm print bed and prints up to 605 mm tall, a build volume of about 305 x 305 x 605 mm. See the full specifications table above for bed type, temperatures and more.

When did the Raise3D Pro2 Plus come out?

Raise3D launched the Pro2 Plus in April 2018.

© 2026 SimplyPrint. All rights reserved. This page and the compatibility, specification and review data on it are compiled by SimplyPrint and may not be copied, scraped, reproduced or republished, in whole or in part, without prior written permission. Printer images are the property of their respective manufacturers and are shown for identification purposes only; SimplyPrint claims no ownership of them. Quoted reviews belong to their authors.