Skip to main content

CreatBot F1000: specs, SimplyPrint compatibility and setup

By CreatBot, China

CreatBot F1000 image

Does it work with SimplyPrint?

Not compatible We're sure

To our knowledge it can't connect to SimplyPrint, not even through OctoPrint or Klipper.

See printers that work

CreatBot F1000 at a glance

The CreatBot F1000 is a 3D printer by CreatBot with a 1000 x 1000 x 1000 mm build volume.

Build volume
1000 x 1000 x 1000 mm
Enclosure
Fully enclosed
Max print speed
120 mm/s
Prints well
PLA, PETG, ABS & ASA, Nylon (PA), Polycarbonate (PC)
Built-in camera
Yes
Connectivity
USB
All specifications

Connect the CreatBot F1000 to SimplyPrint

Does the CreatBot F1000 3D printer work with SimplyPrint, OctoPrint, Mainsail and Fluidd? Each way of connecting it, what it needs, and how to set it up.

  • SimplyPrint

    SimplyPrint

    Not compatible

  • Mainsail Fluidd

    Klipper (Moonraker)

    Not compatible

  • OctoPrint

    OctoPrint

    Directly, over USB

    Not compatible

No known way to connect it to SimplyPrint

Unfortunately, the CreatBot F1000 is currently not, to our knowledge, compatible with OctoPrint, Mainsail, Fluidd, or SimplyPrint. For the best 3D printing experience, consider other 3D printers that are compatible with these softwares.

How we determine compatibility

We consider a printer compatible if it works with one or more of the following:

  • SimplyPrint custom integration for this specific model
  • OctoPrint support (requires the printer to support serial printing)
  • Klipper support (printer can run Klipper, either by flashing compatible firmware or using an external controller/pad)

OctoPrint compatibility is primarily based on whether the printer supports serial communication. If serial printing is not supported, we mark OctoPrint as not compatible.

Note: Some printers have third-party OctoPrint plugins that enable unofficial/custom connections. We don’t maintain a list of these plugins, so they are not reflected in our compatibility data.

See printers that work View Compatible Printers

What slicer to use for the CreatBot F1000

None of the slicers in SimplyPrint's cloud can slice for the CreatBot F1000 that we know of: it doesn't take standard G-code. Use the slicer its maker recommends.

No profile for the CreatBot F1000

We only list slicers you can use in the SimplyPrint cloud, so there may be others for the CreatBot F1000.

No online slicing for the CreatBot F1000

CreatBot F1000 specifications: bed size, print height and more

Its size, temperatures, multi-material and how it connects, from the maker and our own research. Read more by the manufacturer

Size

Build volume 1000 x 1000 x 1000 mm
Bed type Square
Bed size 1000 x 1000 mm
Max print height 1000 mm

Printing

Enclosure Fully enclosed
Max print speed 120 mm/s
Max extruder temperature 420 °C
Has heated bed Yes
Max bed temperature 100 °C
Number of nozzles 1
Toolheads 2
Direct drive No
Probing tool / Auto Bed Leveling Yes
Filament width 1.75 mm

Multi-material

Toolchanger or hotend changer No
IDEX (independent dual extruders) No

Connecting

Connectivity USB
Built-in camera Yes
Supports serial printing No
Shipped firmware Unknown

Files and slicing

Supported file formats G-code (.gcode, .gco, .g)

The printer

Printer manufacturer / brand CreatBot
Printer model name F1000
Made by a company from China

Disclaimer: We strive to keep this information as current and accurate as possible, but cannot guarantee its completeness or reliability. Our data is based on user submissions and manufacturer references.

What filament can the CreatBot F1000 print?

Filament compatibility for the CreatBot F1000: the materials it can handle, judged from its hotend, bed, chamber and enclosure.

Filament Suitability Notes
PLA Great The easiest filament to print. Works on almost any printer; a heated bed helps adhesion but is not required.
PETG Great Comfortably in range (PETG likes a ~230-250C hotend and a ~70-85C bed).
TPU & flexibles With care Possible, but a Bowden extruder makes flexibles harder - print slowly and prefer firmer (higher-shore) TPU.
ABS & ASA Great Enclosed, with a hot enough hotend and bed: ABS and ASA print well.
Nylon (PA) Good Doable with care - dry the filament thoroughly, and an enclosure helps a lot.
Polycarbonate (PC) Good In range for PC. Dry the filament, print slowly, and use an enclosure for the best results.
Carbon-fiber & glass-filled With care Possible if you fit a hardened or wear-resistant nozzle - the abrasive fibers quickly wear a stock brass nozzle.

Tip: this is a general guide from the printer's specs - always check your filament's recommended settings. With SimplyPrint you can save a profile for each spool and track exactly what filament you have in stock.

Printers like the CreatBot F1000 that work with SimplyPrint

Printers from the same maker, of a similar size, printing the same engineering materials or multi-material like it, that you can buy today and that we know work with SimplyPrint.

  • MINGDA MD-1000D 3D printer
    MINGDA MD-1000D
    1000 x 1000 x 1000 mm
    Launched 2023
    Connects with: Klipper (Moonraker)
    Similar build volume · Also prints ABS & ASA, Nylon (PA), Polycarbonate (PC)
    Compatible
  • WASP 3MT HDP 3D printer
    WASP 3MT HDP
    1000 x 1000 x 1000 mm
    Launched November 2021
    Connects with: OctoPrint
    Similar build volume · Also prints ABS & ASA, Nylon (PA), Polycarbonate (PC)
    Compatible
  • CreatBot PEEK-300 3D printer
    CreatBot PEEK-300
    300 x 300 x 400 mm
    Connects with: OctoPrint
    Also by CreatBot · Also prints ABS & ASA, Nylon (PA), Polycarbonate (PC)
    Expected to work
  • MINGDA MD-1000 Pro+ 3D printer
    MINGDA MD-1000 Pro+
    1000 x 1000 x 1000 mm
    Launched 2026
    Connects with: Klipper (Moonraker)
    Similar build volume · Also prints ABS & ASA, Nylon (PA), Polycarbonate (PC)
    Expected to work
Compare 3D printers that work with SimplyPrint All CreatBot printers

Frequently asked questions

Is the CreatBot F1000 compatible with SimplyPrint?

To our knowledge the CreatBot F1000 is not yet supported. SimplyPrint works with 130+ brands and 600+ models via OctoPrint, Klipper and built-in integrations - check the compatibility list for a supported printer.

What slicer should I use for the CreatBot F1000?

None of the slicers in SimplyPrint's cloud can slice for the CreatBot F1000 that we know of: it doesn't take standard G-code. Use the slicer its maker recommends.

What filament can the CreatBot F1000 print?

Based on its specs (hotend up to 420C, heated bed up to 100C), the CreatBot F1000 handles PLA, PETG, ABS & ASA, or Nylon (PA) well. See the full filament guide above for ABS, nylon, PC and composites.

What is the CreatBot F1000's bed size and build volume?

The CreatBot F1000 has a 1000 x 1000 mm print bed and prints up to 1000 mm tall, a build volume of about 1000 x 1000 x 1000 mm. See the full specifications table above for bed type, temperatures and more.

© 2026 SimplyPrint. All rights reserved. This page and the compatibility, specification and review data on it are compiled by SimplyPrint and may not be copied, scraped, reproduced or republished, in whole or in part, without prior written permission. Printer images are the property of their respective manufacturers and are shown for identification purposes only; SimplyPrint claims no ownership of them. Quoted reviews belong to their authors.