# BambuStudio Settings ## Print Settings ### Quality #### Layer height - `layer_height` - Layer height: Slicing height for each layer. Smaller layer height means more accurate and more printing time - `initial_layer_print_height` - Initial layer height: Height of initial layer. Making initial layer height thick slightly can improve build plate adhensio... #### Line width - `line_width` - Default: Default line width if some line width is set to be zero - `initial_layer_line_width` - Initial layer: Line width of initial layer - `outer_wall_line_width` - Outer wall: Line width of outer wall - `inner_wall_line_width` - Inner wall: Line width of inner wall - `top_surface_line_width` - Top surface: Line width for top surfaces - `sparse_infill_line_width` - Sparse infill: Line width of internal sparse infill - `internal_solid_infill_line_width` - Internal solid infill: Line width of internal solid infill - `support_line_width` - Support: Line width of support #### Seam - `seam_position` - Seam position: The start position to print each part of outer wall - `seam_placement_away_from_overhangs` - Seam placement away from overhangs(experimental): Ensure seam placement away from overhangs for alignment and backing modes. - `seam_gap` - Seam gap: In order to reduce the visibility of the seam in a closed loop extrusion, the loop is interrupted an... - `seam_slope_conditional` - Smart scarf seam application: Apply scarf joints only to smooth perimeters where traditional seams do not conceal the seams at sha... - `scarf_angle_threshold` - Scarf application angle threshold: This option sets the threshold angle for applying a conditional scarf joint seam. If the seam angle ... - `seam_slope_entire_loop` - Scarf around entire wall: The scarf extends to the entire length of the wall. - `seam_slope_steps` - Scarf steps: Minimum number of segments of each scarf. - `seam_slope_inner_walls` - Scarf joint for inner walls: Use scarf joint for inner walls as well. - `override_filament_scarf_seam_setting` - Override filament scarf seam setting: Overrider filament scarf seam setting and could control settings by modifier. - `seam_slope_type` - Scarf seam type: Set scarf seam type for this filament. This setting could minimize seam visibiliy. - `seam_slope_start_height` - Scarf start height: This amount can be specified in millimeters or as a percentage of the current layer height. - `seam_slope_gap` - Scarf slope gap: In order to reduce the visiblity of the seam in closed loop, the inner wall and outer wall are short... - `seam_slope_min_length` - Scarf length: Length of the scarf. Setting this parameter to zero effectively disables the scarf. - `wipe_speed` - Wipe speed: The wipe speed is determined by the speed setting specified in this configuration.If the value is ex... - `role_base_wipe_speed` - Role-based wipe speed: The wipe speed is determined by speed of current extrusion role. e.g if a wipe action is executed im... #### Precision - `slice_closing_radius` - Slice gap closing radius: Cracks smaller than 2x gap closing radius are being filled during the triangle mesh slicing. The gap... - `resolution` - Resolution: G-code path is generated after simplifying the contour of model to avoid too many points and gcode l... - `enable_arc_fitting` - Arc fitting: Enable this to get a G-code file which has G2 and G3 moves. And the fitting tolerance is the same as... - `xy_hole_compensation` - X-Y hole compensation: Holes of object will be grown or shrunk in XY plane by the configured value. Positive value makes ho... - `xy_contour_compensation` - X-Y contour compensation: Contour of object will be grown or shrunk in XY plane by the configured value. Positive value makes ... - `enable_circle_compensation` - Auto circle contour-hole compensation: Expirment feature to compensate the circle holes and circle contour. This feature is used to improve... - `circle_compensation_manual_offset` - User Customized Offset: If you want to have tighter or looser assemble, you can set this value. When it is positive, it indi... - `elefant_foot_compensation` - Elephant foot compensation: Shrink the initial layer on build plate to compensate for elephant foot effect - `precise_outer_wall` - Precise wall: Improve shell precision by adjusting outer wall spacing. This also improves layer consistency. - `precise_z_height` - Precise Z height: Enable this to get precise z height of object after slicing. It will get the precise object height b... #### Ironing - `ironing_type` - Ironing Type: Ironing is using small flow to print on same height of surface again to make flat surface more smoot... - `ironing_pattern` - Ironing Pattern - `ironing_speed` - Ironing speed: Print speed of ironing lines - `ironing_flow` - Ironing flow: The amount of material to extrude during ironing. Relative to flow of normal layer height. Too high ... - `ironing_spacing` - Ironing line spacing: The distance between the lines of ironing - `ironing_inset` - Ironing inset: The distance to keep the from the edges of ironing line. 0 means not apply. - `ironing_direction` - ironing direction: Angle for ironing, which controls the relative angle between the top surface and ironing #### Wall generator - `wall_generator` - Wall generator: Classic wall generator produces walls with constant extrusion width and for very thin areas is used ... - `wall_transition_angle` - Wall transitioning threshold angle: When to create transitions between even and odd numbers of walls. A wedge shape with an angle greate... - `wall_transition_filter_deviation` - Wall transitioning filter margin: Prevent transitioning back and forth between one extra wall and one less. This margin extends the ra... - `wall_transition_length` - Wall transition length: When transitioning between different numbers of walls as the part becomes thinner, a certain amount ... - `wall_distribution_count` - Wall distribution count: The number of walls, counted from the center, over which the variation needs to be spread. Lower val... - `min_bead_width` - Minimum wall width: Width of the wall that will replace thin features (according to the Minimum feature size) of the mod... - `min_feature_size` - Minimum feature size: Minimum thickness of thin features. Model features that are thinner than this value will not be prin... #### Advanced - `wall_sequence` - Order of walls: Print sequence of inner wall and outer wall. - `is_infill_first` - Print infill first: Order of wall/infill. false means print wall first. - `bridge_flow` - Bridge flow: Decrease this value slightly(for example 0.9) to reduce the amount of material for bridge, to improv... - `thick_bridges` - Thick bridges: If enabled, bridges are more reliable, can bridge longer distances, but may look worse. If disabled,... - `print_flow_ratio` - Object flow ratio: The flow ratio set by object, the meaning is the same as flow ratio. - `top_solid_infill_flow_ratio` - Top surface flow ratio: This factor affects the amount of material for top solid infill. You can decrease it slightly to hav... - `initial_layer_flow_ratio` - Initial layer flow ratio: This factor affects the amount of material for the initial layer - `top_one_wall_type` - Only one wall on top surfaces: Use only one wall on flat top surface, to give more space to the top infill pattern. Could be applie... - `top_area_threshold` - Top area threshold: The min width of top areas in percentage of perimeter line width. - `only_one_wall_first_layer` - Only one wall on first layer: Use only one wall on the first layer of model - `detect_overhang_wall` - Detect overhang wall: Detect the overhang percentage relative to line width and use different speed to print. For 100 perc... - `smooth_speed_discontinuity_area` - Smooth speed discontinuity area: Add the speed transition between discontinuity area. - `smooth_coefficient` - Smooth coefficient: The smaller the number, the longer the speed transition path. 0 means not apply. - `reduce_crossing_wall` - Avoid crossing wall: Detour and avoid traveling across wall which may cause blob on surface - `max_travel_detour_distance` - Avoid crossing wall - Max detour length: Maximum detour distance for avoiding crossing wall. Don't detour if the detour distance is larger th... - `avoid_crossing_wall_includes_support` - Avoid crossing wall - Includes support: Including support while avoiding crossing wall. - `z_direction_outwall_speed_continuous` - Smoothing wall speed along Z(experimental): Smoothing outwall speed in z direction to get better surface quality. Print time will increases. Thi... ### Strength #### Walls - `wall_loops` - Wall loops: Number of walls of every layer - `embedding_wall_into_infill` - Embedding the wall into the infill: Embedding the wall into parts where the wall loops are absent ensures that the wall connects seamles... - `detect_thin_wall` - Detect thin wall: Detect thin wall which can't contain two line width. And use single line to print. Maybe printed not... #### Top\/bottom shells - `interface_shells` - Interface shells: Force the generation of solid shells between adjacent materials/volumes. Useful for multi-extruder p... - `top_surface_pattern` - Top surface pattern: Line pattern of top surface infill - `top_surface_density` - Top surface density: Density of top surface infill, 100% means a fully solid filled top layer.Lower values create a textu... - `top_shell_layers` - Top shell layers: This is the number of solid layers of top shell, including the top surface layer. When the thickness... - `top_shell_thickness` - Top shell thickness: The number of top solid layers is increased when slicing if the thickness calculated by top shell la... - `top_color_penetration_layers` - Top paint penetration layers: This is the number of layers of top paint penetration. - `bottom_surface_pattern` - Bottom surface pattern: Line pattern of bottom surface infill, not bridge infill - `bottom_surface_density` - Bottom surface density: Density of bottom surface infill, 100% means a fully solid filled top layer.Lower values create a te... - `bottom_shell_layers` - Bottom shell layers: This is the number of solid layers of bottom shell, including the bottom surface layer. When the thi... - `bottom_shell_thickness` - Bottom shell thickness: The number of bottom solid layers is increased when slicing if the thickness calculated by bottom sh... - `bottom_color_penetration_layers` - Bottom paint penetration layers: This is the number of layers of bottom paint penetration. - `infill_instead_top_bottom_surfaces` - Use infill instead of top and bottom surfaces: Using infill instead of top and bottom surfaces. - `internal_solid_infill_pattern` - Internal solid infill pattern: Line pattern of internal solid infill. if the detect narrow internal solid infill be enabled, the co... #### Sparse infill - `sparse_infill_density` - Sparse infill density: Density of internal sparse infill, 100% means solid throughout - `fill_multiline` - Fill multiline: Using multiple lines for the infill pattern, if supported by infill pattern. - `sparse_infill_pattern` - Sparse infill pattern: Line pattern for internal sparse infill - `locked_skin_infill_pattern` - Skin infill pattern: Line pattern for skin - `skin_infill_density` - Skin infill density: The portion of the model's outer surface within a certain depth range is called the skin. This param... - `locked_skeleton_infill_pattern` - Skeleton infill pattern: Line pattern for skeleton - `skeleton_infill_density` - Skeleton infill density: The remaining part of the model contour after removing a certain depth from the surface is called th... - `infill_lock_depth` - Infill lock depth: The parameter sets the overlapping depth between the interior and skin. - `skin_infill_depth` - Skin infill depth: The parameter sets the depth of skin. - `skin_infill_line_width` - Skin line width: Adjust the line width of the selected skin paths. - `skeleton_infill_line_width` - Skeleton line width: Adjust the line width of the selected skeleton paths. - `symmetric_infill_y_axis` - Symmetric infill y axis: If the model has two parts that are symmetric about the y-axis, and you want these parts to have sym... - `infill_shift_step` - Infill shift step: This parameter adds a slight displacement to each layer of infill to create a cross texture. - `sparse_infill_lattice_angle_1` - Lattice angle 1: The angle of the first set of 2D lattice elements in the Z direction. Zero is vertical. - `sparse_infill_lattice_angle_2` - Lattice angle 2: The angle of the second set of 2D lattice elements in the Z direction. Zero is vertical. - `infill_rotate_step` - Infill rotate step: This parameter adds a slight rotation to each layer of infill to create a cross texture. - `sparse_infill_anchor` - Length of sparse infill anchor: Connect a sparse infill line to an internal perimeter with a short segment of an additional perimete... - `sparse_infill_anchor_max` - Maximum length of sparse infill anchor: Connect a sparse infill line to an internal perimeter with a short segment of an additional perimete... - `filter_out_gap_fill` - Filter out tiny gaps: Filter out gaps smaller than the threshold specified. Gaps smaller than this threshold will be ignor... #### Advanced - `infill_wall_overlap` - Infill/Wall overlap: Infill area is enlarged slightly to overlap with wall for better bonding. The percentage value is re... - `infill_direction` - Infill direction: Angle for sparse infill pattern, which controls the start or main direction of line - `bridge_angle` - Bridge direction: Bridging angle override. If left to zero, the bridging angle will be calculated automatically. Other... - `minimum_sparse_infill_area` - Minimum sparse infill threshold: Sparse infill area which is smaller than threshold value is replaced by internal solid infill - `infill_combination` - Infill combination: Automatically Combine sparse infill of several layers to print together to reduce time. Wall is stil... - `detect_narrow_internal_solid_infill` - Detect narrow internal solid infill: This option will auto detect narrow internal solid infill area. If enabled, concentric pattern will ... - `ensure_vertical_shell_thickness` - Ensure vertical shell thickness: Add solid infill near sloping surfaces to guarantee the vertical shell thickness (top+bottom solid l... - `detect_floating_vertical_shell` - Detect floating vertical shells: Detect overhang paths in vertical shells and slow them by bridge speed. ### Speed #### Initial layer speed - `initial_layer_speed#0` - `initial_layer_infill_speed#0` #### Other layers speed - `outer_wall_speed#0` - `inner_wall_speed#0` - `small_perimeter_speed#0` - `small_perimeter_threshold#0` - `sparse_infill_speed#0` - `internal_solid_infill_speed#0` - `vertical_shell_speed#0` - `top_surface_speed#0` - `enable_overhang_speed#0` - Overhang speed: `overhang_1_4_speed#0`, `overhang_2_4_speed#0`, `overhang_3_4_speed#0`, `overhang_4_4_speed#0`, `overhang_totally_speed#0` - `enable_height_slowdown#0` - `slowdown_start_height#0` - `slowdown_start_speed#0` - `slowdown_start_acc#0` - `slowdown_end_height#0` - `slowdown_end_speed#0` - `slowdown_end_acc#0` - `bridge_speed#0` - `gap_infill_speed#0` - `support_speed#0` - `support_interface_speed#0` #### Travel speed - `travel_speed#0` #### Acceleration - `default_acceleration#0` - `travel_acceleration#0` - `initial_layer_travel_acceleration#0` - `initial_layer_acceleration#0` - `outer_wall_acceleration#0` - `inner_wall_acceleration#0` - `top_surface_acceleration#0` - `sparse_infill_acceleration#0` - `accel_to_decel_enable` - Enable accel_to_decel: Klipper's max_accel_to_decel will be adjusted automatically - `accel_to_decel_factor` - accel_to_decel: Klipper's max_accel_to_decel will be adjusted to this percent of acceleration #### Jerk(XY) - `default_jerk` - Default: Default jerk - `outer_wall_jerk` - Outer wall: Jerk of outer walls - `inner_wall_jerk` - Inner wall: Jerk of inner walls - `infill_jerk` - Infill: Jerk of infill - `top_surface_jerk` - Top surface: Jerk of top surface - `initial_layer_jerk` - First layer: Jerk of first layer - `travel_jerk` - Travel: Jerk of travel ### Support #### Support - `enable_support` - Enable support: Enable support generation. - `support_type` - Type: normal(auto) and tree(auto) is used to generate support automatically. If normal(manual) or tree(man... - `support_style` - Style: Style and shape of the support. For normal support, projecting the supports into a regular grid will... - `support_threshold_angle` - Threshold angle: Support will be generated for overhangs whose slope angle is below the threshold. - `support_on_build_plate_only` - On build plate only: Don't create support on model surface, only on build plate - `support_critical_regions_only` - Support critical regions only: Only create support for critical regions including sharp tail, cantilever, etc. - `support_remove_small_overhang` - Remove small overhangs: Remove small overhangs that possibly need no supports. #### Raft - `raft_layers` - Raft layers: Object will be raised by this number of support layers. Use this function to avoid warping when prin... - `raft_contact_distance` - Raft contact Z distance: Z gap between object and raft. Ignored for soluble interface #### Support filament - `support_filament` - Support/raft base: Filament to print support base and raft. "Default" means no specific filament for support and curren... - `support_interface_filament` - Support/raft interface: Filament to print support interface. "Default" means no specific filament for support interface and ... - `support_interface_not_for_body` - Avoid interface filament for base: Avoid using support interface filament to print support base if possible. #### Support ironing - `enable_support_ironing` - Enable ironing support interface: Ironing is using small flow to print on same height of surface again to make flat surface more smoot... - `support_ironing_pattern` - Support ironing pattern - `support_ironing_speed` - Support ironing speed: Print speed of ironing lines - `support_ironing_flow` - Support ironing flow: The amount of material to extrude during ironing. Relative to flow of normal layer height. Too high ... - `support_ironing_spacing` - Support ironing line spacing: The distance between the lines of ironing - `support_ironing_inset` - Support ironing inset: The distance to keep the from the edges of ironing line. 0 means not apply. - `support_ironing_direction` - Support ironing direction: Angle for ironing, which controls the relative angle between the top surface and ironing #### Advanced - `raft_first_layer_density` - Initial layer density: Density of the first raft or support layer - `raft_first_layer_expansion` - Initial layer expansion: Expand the first raft or support layer to improve bed plate adhesion, -1 means auto - `tree_support_wall_count` - Support wall loops: This setting specifies the count of support walls in the range of [-1,2]. -1 means auto, and 0 means... - `support_top_z_distance` - Top Z distance: The z gap between the top support interface and object - `support_bottom_z_distance` - Bottom Z distance: The z gap between the bottom support interface and object - `support_base_pattern` - Base pattern: Line pattern of support - `support_base_pattern_spacing` - Base pattern spacing: Spacing between support lines - `support_angle` - Pattern angle: Use this setting to rotate the support pattern on the horizontal plane. - `support_interface_top_layers` - Top interface layers: Number of top interface layers - `support_interface_bottom_layers` - Bottom interface layers: Number of bottom interface layers - `support_interface_pattern` - Interface pattern: Line pattern of support interface. Default pattern for support interface is Rectilinear Interlaced - `support_interface_spacing` - Top interface spacing: Spacing of interface lines. Zero means solid interface.And zero spacing is required to access the en... - `support_bottom_interface_spacing` - Bottom interface spacing: Spacing of bottom interface lines. Zero means solid interface - `support_expansion` - Normal Support expansion: Expand (+) or shrink (-) the horizontal span of normal support - `support_object_xy_distance` - Support/object xy distance: XY separation between an object and its support - `top_z_overrides_xy_distance` - Z overrides X/Y: When top z distance overrides support/object xy distance, give priority to ensuring that supports ar... - `support_object_first_layer_gap` - Support/object first layer gap: XY separation between an object and its support at the first layer. - `bridge_no_support` - Don't support bridges: Don't support the whole bridge area which makes support very large. Bridge usually can be printing d... - `max_bridge_length` - Max bridge length: Max length of bridges that don't need support. Set it to 0 if you want all bridges to be supported, ... - `independent_support_layer_height` - Independent support layer height: Support layer uses layer height independent with object layer. This is to support customizing z-gap ... #### Tree Support - `tree_support_branch_distance` - Branch distance: This setting determines the distance between neighboring tree support nodes. - `tree_support_branch_diameter` - Branch diameter: This setting determines the initial diameter of support nodes. - `tree_support_branch_angle` - Branch angle: This setting determines the maximum overhang angle that t he branches of tree support allowed to mak... - `tree_support_branch_diameter_angle` - Branch diameter angle: The angle of the branches' diameter as they gradually become thicker towards the bottom. An angle of... ### Others #### Bed adhension - `skirt_loops` - Skirt loops: Number of loops for the skirt. Zero means disabling skirt - `skirt_height` - Skirt height: How many layers of skirt. Usually only one layer - `skirt_distance` - Skirt distance: Distance from skirt to brim or object - `brim_type` - Brim type: This controls the generation of the brim at outer and/or inner side of models. Auto means the brim w... - `brim_width` - Brim width: Distance from model to the outermost brim line - `brim_object_gap` - Brim-object gap: A gap between innermost brim line and object can make brim be removed more easily #### Prime tower - `enable_prime_tower` - Enable: The wiping tower can be used to clean up the residue on the nozzle and stabilize the chamber pressur... - `prime_tower_skip_points` - Skip points: The wall of prime tower will skip the start points of wipe path - `prime_tower_enable_framework` - Internal ribs: Enable internal ribs to increase the stability of the prime tower. - `prime_tower_width` - Width: Width of prime tower - `prime_tower_max_speed` - Max speed: The maximum printing speed on the prime tower excluding ramming. - `prime_tower_brim_width` - Brim width: Brim width of prime tower, negative number means auto calculated width based on the height of prime ... - `prime_tower_infill_gap` - Infill gap: Infill gap - `prime_tower_rib_wall` - Rib wall: The wall of prime tower will add four ribs and make its cross-section as close to a square as possib... - `prime_tower_extra_rib_length` - Extra rib length: Positive values can increase the size of the rib wall, while negative values can reduce the size.How... - `prime_tower_rib_width` - Rib width: Rib width is always less than half the prime tower side length. - `prime_tower_fillet_wall` - Fillet wall: The wall of prime tower will fillet #### Flush options - `flush_into_infill` - Flush into objects' infill: Purging after filament change will be done inside objects' infills. This may lower the amount of was... - `flush_into_objects` - Flush into this object: This object will be used to purge the nozzle after a filament change to save filament and decrease t... - `flush_into_support` - Flush into objects' support: Purging after filament change will be done inside objects' support. This may lower the amount of was... #### Special mode - `slicing_mode` - Slicing Mode: Use "Even-odd" for 3DLabPrint airplane models. Use "Close holes" to close all holes in the model. - `print_sequence` - Print sequence: Print sequence, layer by layer or object by object - `spiral_mode` - Spiral vase: Spiralize smooths out the z moves of the outer contour. And turns a solid model into a single walled... - `spiral_mode_smooth` - Smooth Spiral: Smooth Spiral smoothes out X and Y moves as wellresulting in no visible seam at all, even in the XY ... - `spiral_mode_max_xy_smoothing` - Max XY Smoothing: Maximum distance to move points in XY to try to achieve a smooth spiralIf expressed as a %, it will ... - `timelapse_type` - Timelapse: If smooth or traditional mode is selected, a timelapse video will be generated for each print. After... - `fuzzy_skin` - Fuzzy Skin: Randomly jitter while printing the wall, so that the surface has a rough look. This setting controls... - `fuzzy_skin_point_distance` - Fuzzy skin point distance: The average distance between the random points introduced on each line segment - `fuzzy_skin_thickness` - Fuzzy skin thickness: The width within which to jitter. It's adversed to be below outer wall line width #### Advanced - `enable_wrapping_detection` - Enable clumping detection: Enable clumping detection - `interlocking_beam` - Use beam interlocking: Generate interlocking beam structure at the locations where different filaments touch. This improves... - `mmu_segmented_region_interlocking_depth` - Interlocking depth of a segmented region: Interlocking depth of a segmented region. Zero disables this feature. - `interlocking_beam_width` - Interlocking beam width: The width of the interlocking structure beams. - `interlocking_orientation` - Interlocking direction: Orientation of interlock beams. - `interlocking_beam_layer_count` - Interlocking beam layers: The height of the beams of the interlocking structure, measured in number of layers. Less layers is ... - `interlocking_depth` - Interlocking depth: The distance from the boundary between filaments to generate interlocking structure, measured in cel... - `interlocking_boundary_avoidance` - Interlocking boundary avoidance: The distance from the outside of a model where interlocking structures will not be generated, measur... - `sparse_infill_filament` - Sparse infill filament: Filament to print internal sparse infill. - `solid_infill_filament` - Solid infill filament: Filament to print solid infill - `wall_filament` - Walls filament: Filament to print walls #### G-code output - `reduce_infill_retraction` - Reduce infill retraction: Don't retract when the travel is in infill area absolutely. That means the oozing can't been seen. T... - `gcode_add_line_number` - Add line number: Enable this to add line number(Nx) at the beginning of each G-Code line - `exclude_object` - Exclude objects: Enable this option to add EXCLUDE OBJECT command in g-code for klipper firmware printer - `filename_format` #### Post-processing scripts - `post_process` #### Notes - `process_notes` - Process notes: You can put your notes regarding the process here. ### icon_data #### Quality - `param_advanced.svg` - ` <\/g> <\/clipPath> <\/defs> <\/svg> ` #### Strength - `param_advanced.svg` - ` <\/g> <\/clipPath> <\/defs> <\/svg> ` #### Speed - `param_acceleration.svg` - ` <\/g> <\/clipPath> <\/defs> <\/svg> ` #### Support - `param_advanced.svg` - ` <\/g> <\/clipPath> <\/defs> <\/svg> ` #### Others - `note.svg` - ` <\/g> <\/g> <\/g> <\/g> <\/g> <\/g> <\/svg> ` ## Machine/Printer Settings ### Basic information #### Printable space - `printable_area` - Printable area - `bed_exclude_area` - Bed exclude area: Unprintable area in XY plane. For example, X1 Series printers use the front left corner to cut filam... - `printable_height` - Printable height: Maximum printable height which is limited by mechanism of printer - `best_object_pos` - Best object position: Best auto arranging position in range [0,1] w.r.t. bed shape. #### Advanced - `printer_structure` - Printer structure: The physical arrangement and components of a printing device - `gcode_flavor` - G-code flavor: What kind of gcode the printer is compatible with - `apply_top_surface_compensation` - Apply top surface compensation: Enable this option to extend the travel distance between top surface lines, improving the adhesion b... - `thumbnail_size` - Thumbnail size: Decides the size of thumbnail stored in gcode files - `scan_first_layer` - Scan first layer: Enable this to enable the camera on printer to check the quality of first layer - `use_relative_e_distances` - Use relative E distances: If your firmware requires relative E values, check this, otherwise leave it unchecked. Must use rela... - `use_firmware_retraction` - Use firmware retraction: Convert the retraction moves to G10 and G11 gcode - `bed_temperature_formula` - Bed temperature type: This option determines how the bed temperature is set during slicing: based on the temperature of th... - `machine_load_filament_time` - Filament load time: Time to load new filament when switch filament. For statistics only - `machine_unload_filament_time` - Filament unload time: Time to unload old filament when switch filament. For statistics only - `machine_switch_extruder_time` - Extruder switch time: Time to switch extruder. For statistics only - `machine_hotend_change_time` - Hotend change time: Time to change hotend. #### Extruder Clearance - `extruder_clearance_max_radius` - Max Radius: Max clearance radius around extruder. Used for collision avoidance in by-object printing. - `extruder_clearance_dist_to_rod` - Distance to rod: Horizontal distance of the nozzle tip to the rod's farther edge. Used for collision avoidance in by-... - `extruder_clearance_height_to_rod` - Height to rod: Distance of the nozzle tip to the lower rod. Used for collision avoidance in by-object printing. - `extruder_clearance_height_to_lid` - Height to lid: Distance of the nozzle tip to the lid. Used for collision avoidance in by-object printing. #### Accessory - `nozzle_type` - Nozzle type: The metallic material of nozzle. This determines the abrasive resistance of nozzle, and what kind of... - `auxiliary_fan` - Auxiliary part cooling fan: Enable this option if machine has auxiliary part cooling fan - `fan_direction` - Fan direction: Cooling fan direction of the printer - `support_chamber_temp_control` - Support control chamber temperature: This option is enabled if machine support controlling chamber temperature - `support_air_filtration` - Air filtration enhancement: Enable this if printer support air filtration enhancement. - `cooling_filter_enabled` - Use cooling filter: Enable this if printer support cooling filter ### Machine gcode #### Machine start G-code - `machine_start_gcode` - Start G-code: Start G-code when start the whole printing #### Machine end G-code - `machine_end_gcode` - End G-code: End G-code when finish the whole printing #### Printing by object G-code - `printing_by_object_gcode` - Between Object Gcode: Insert Gcode between objects. This parameter will only come into effect when you print your models o... #### Layer change G-code - `layer_change_gcode` - Layer change G-code: This gcode part is inserted at every layer change after lift z #### Time lapse G-code - `time_lapse_gcode` - Time lapse G-code #### Clumping Detection G-code - `wrapping_detection_gcode` - Clumping detection G-code #### Change filament G-code - `change_filament_gcode` - Change filament G-code: This gcode is inserted when change filament, including T command to trigger tool change #### Pause G-code - `machine_pause_gcode` - Pause G-code: This G-code will be used as a code for the pause print. User can insert pause G-code in gcode viewer #### Template Custom G-code - `template_custom_gcode` - Custom G-code: This G-code will be used as a custom code ### Motion ability #### Speed limitation - `machine_max_speed_x#0` - `machine_max_speed_y#0` - `machine_max_speed_z#0` - `machine_max_speed_e#0` #### Acceleration limitation - `machine_max_acceleration_x#0` - `machine_max_acceleration_y#0` - `machine_max_acceleration_z#0` - `machine_max_acceleration_e#0` - `machine_max_acceleration_extruding#0` - `machine_max_acceleration_retracting#0` - `machine_max_acceleration_travel#0` #### Jerk limitation - `machine_max_jerk_x#0` - `machine_max_jerk_y#0` - `machine_max_jerk_z#0` - `machine_max_jerk_e#0` ### Extruder #### Basic information - `extruder_type#0` - `nozzle_diameter#0` - `nozzle_volume#0` - `extruder_printable_height#0` - `extruder_printable_area#0` #### Layer height limits - `min_layer_height#0` - `max_layer_height#0` #### Position - `extruder_offset` - Extruder offset #### Retraction - `retraction_length#0` - `z_hop#0` - `retract_lift_above#0` - `retract_lift_below#0` - `z_hop_types#0` - `retraction_speed#0` - `deretraction_speed#0` - `retract_restart_extra#0` - `retraction_minimum_travel#0` - `retract_when_changing_layer#0` - `wipe#0` - `wipe_distance#0` - `retract_before_wipe#0` #### Retraction when switching material - `retract_length_toolchange#0` - `retract_restart_extra_toolchange#0` - `long_retractions_when_cut#0` - `retraction_distances_when_cut#0` ### Notes #### Notes - `printer_notes` - Printer notes: You can put your notes regarding the printer here. ### icon_data #### Basic information - `param_advanced.svg` - ` <\/g> <\/clipPath> <\/defs> <\/svg> ` #### Machine gcode - `param_gcode.svg` - ` <\/g> <\/clipPath> <\/defs> <\/svg> ` #### Motion ability - `param_acceleration.svg` - ` <\/g> <\/clipPath> <\/defs> <\/svg> ` #### Extruder - `param_retraction.svg` - ` <\/svg> ` #### Notes - `note.svg` - ` <\/g> <\/g> <\/g> <\/g> <\/g> <\/g> <\/svg> ` ## Filament Settings ### Filament #### Basic information - `filament_type` - Type: The material type of filament - `filament_vendor` - Vendor: Vendor of filament. For show only - `filament_soluble` - Soluble material: Soluble material is commonly used to print support and support interface - `filament_is_support` - Support material: Support material is commonly used to print support and support interface - `impact_strength_z` - Impact Strength Z - `required_nozzle_HRC` - Required nozzle HRC: Minimum HRC of nozzle required to print the filament. Zero means no checking of nozzle's HRC. - `default_filament_colour` - Default color: Default filament color - `filament_diameter` - Diameter: Filament diameter is used to calculate extrusion in gcode, so it's important and should be accurate - `filament_adhesiveness_category` - Adhesiveness Category: Filament category - `filament_flow_ratio#0` - `enable_pressure_advance` - Enable pressure advance: Enable pressure advance, auto calibration result will be overwriten once enabled. Useless for Bambu ... - `pressure_advance` - Pressure advance: Pressure advance(Klipper) AKA Linear advance factor(Marlin). Useless for Bambu Printer - `filament_density` - Density: Filament density. For statistics only - `filament_shrink` - Shrinkage: Enter the shrinkage percentage that the filament will get after cooling (94% if you measure 94mm ins... - `filament_velocity_adaptation_factor` - Velocity Adaptation Factor: This parameter reflects the speed at which a material transitions from one state to another. It, alo... - `filament_cost` - `temperature_vitrification` - Softening temperature: The material softens at this temperature, so when the bed temperature is equal to or greater than it... - `filament_cooling_before_tower` - Wipe tower cooling: Temperature drop before entering filament tower - `filament_tower_interface_pre_extrusion_dist` - Interface layer pre-extrusion distance: Pre-extrusion distance for prime tower interface layer (where different materials meet). - `filament_tower_interface_pre_extrusion_length` - Interface layer pre-extrusion length: Pre-extrusion length for prime tower interface layer (where different materials meet). - `filament_tower_ironing_area` - Tower ironing area: Ironing area for prime tower interface layer (where different materials meet). - `filament_tower_interface_purge_volume` - Interface layer purge length: Purge length for prime tower interface layer (where different materials meet). - `filament_tower_interface_print_temp` - Interface layer print temperature: Print temperature for prime tower interface layer (where different materials meet). If set to -1, us... - Filament prime volume: `filament_prime_volume`, `filament_prime_volume_nc` - Filament ramming length: `filament_change_length`, `filament_change_length_nc` - Travel time after ramming: `filament_ramming_travel_time#0`, `filament_ramming_travel_time_nc#0` - Precooling target temperature: `filament_pre_cooling_temperature#0`, `filament_pre_cooling_temperature_nc#0` - Recommended nozzle temperature: `nozzle_temperature_range_low`, `nozzle_temperature_range_high` #### Print temperature - `chamber_temperatures` - Chamber temperature: Higher chamber temperature can help suppress or reduce warping and potentially lead to higher interl... - Bambu Cool Plate SuperTack: `supertack_plate_temp_initial_layer`, `supertack_plate_temp` - Cool Plate: `cool_plate_temp_initial_layer`, `cool_plate_temp` - Engineering Plate: `eng_plate_temp_initial_layer`, `eng_plate_temp` - Smooth PEI Plate \/ High Temp Plate: `hot_plate_temp_initial_layer`, `hot_plate_temp` - Textured PEI Plate: `textured_plate_temp_initial_layer`, `textured_plate_temp` - Nozzle: `nozzle_temperature_initial_layer#0`, `nozzle_temperature#0` #### Volumetric speed limitation - `filament_adaptive_volumetric_speed#0` - `filament_max_volumetric_speed#0` - Ramming volumetric speed: `filament_ramming_volumetric_speed#0`, `filament_ramming_volumetric_speed_nc#0` #### Filament scarf seam settings - `filament_scarf_seam_type` - Scarf seam type: Set scarf seam type for this filament. This setting could minimize seam visibiliy. - `filament_scarf_height` - Scarf start height: This amount can be specified in millimeters or as a percentage of the current layer height. - `filament_scarf_gap` - Scarf slope gap: In order to reduce the visiblity of the seam in closed loop, the inner wall and outer wall are short... - `filament_scarf_length` - Scarf length: Length of the scarf. Setting this parameter to zero effectively disables the scarf. ### Cooling #### Cooling for specific layer - Special cooling settings: `close_fan_the_first_x_layers`, `first_x_layer_fan_speed` #### Part cooling fan - Min fan speed threshold: `fan_min_speed`, `fan_cooling_layer_time` - Max fan speed threshold: `fan_max_speed`, `slow_down_layer_time` - `reduce_fan_stop_start_freq` - Keep fan always on: If enable this setting, part cooling fan will never be stopped and will run at least at minimum spee... - `slow_down_for_layer_cooling` - Slow printing down for better layer cooling: Enable this option to slow printing speed down to make the final layer time not shorter than the lay... - `no_slow_down_for_cooling_on_outwalls` - Don't slow down outer walls: If enabled, this setting will ensure external perimeters are not slowed down to meet the minimum lay... - `slow_down_min_speed#0` - `enable_overhang_bridge_fan` - Force cooling for overhang and bridge: Enable this option to optimize part cooling fan speed for overhang and bridge to get better cooling - `overhang_fan_threshold` - Cooling overhang threshold: Force cooling fan to be specific speed when overhang degree of printed part exceeds this value. Expr... - `overhang_threshold_participating_cooling` - Overhang threshold for participating cooling: Decide which overhang part join the cooling function to slow down the speed.Expressed as percentage ... - `overhang_fan_speed` - Fan speed for overhang: Force part cooling fan to be at this speed when printing bridge or overhang wall which has large ove... - `pre_start_fan_time` - Pre start fan time: Force fan start early(0-5 second) when encountering overhangs. This is because the fan needs time to... #### Auxiliary part cooling fan - `additional_cooling_fan_speed` - Fan speed: Speed of auxiliary part cooling fan. Auxiliary fan will run at this speed during printing except the... #### Exhaust fan - `activate_air_filtration` - Activate air filtration: Activate for better air filtration - `during_print_exhaust_fan_speed` - Fan speed: Speed of exhaust fan during printing.This speed will overwrite the speed in filament custom gcode - `complete_print_exhaust_fan_speed` - Fan speed: Speed of exhuast fan after printing completes ### Setting Overrides #### Retraction - `filament_retraction_length#0` - `filament_z_hop#0` - `filament_z_hop_types#0` - `filament_retraction_speed#0` - `filament_deretraction_speed#0` - `filament_retract_length_nc#0` - `filament_retract_restart_extra#0` - `filament_retraction_minimum_travel#0` - `filament_retract_when_changing_layer#0` - `filament_wipe#0` - `filament_wipe_distance#0` - `filament_retract_before_wipe#0` - `filament_long_retractions_when_cut#0` - `filament_retraction_distances_when_cut#0` #### Speed - `override_process_overhang_speed#0` - `filament_enable_overhang_speed#0` - `filament_overhang_1_4_speed#0` - `filament_overhang_2_4_speed#0` - `filament_overhang_3_4_speed#0` - `filament_overhang_4_4_speed#0` - `filament_overhang_totally_speed#0` - `filament_bridge_speed#0` ### Advanced #### Filament start G-code - `filament_start_gcode` - Start G-code: Start G-code when start the printing of this filament #### Filament end G-code - `filament_end_gcode` - End G-code: End G-code when finish the printing of this filament ### Notes #### Notes - `filament_notes` - Filament notes: You can put your notes regarding the filament here. ### Multi Filament #### Multi Filament - `long_retractions_when_ec#0` - `retraction_distances_when_ec#0` ### icon_data #### Filament - `param_volumetric_speed.svg` - ` <\/svg> ` #### Cooling - `param_cooling_fan.svg` - ` <\/g> <\/clipPath> <\/defs> <\/svg> ` #### Setting Overrides - `param_speed.svg` - ` <\/g> <\/clipPath> <\/defs> <\/svg> ` #### Advanced - `param_gcode.svg` - ` <\/g> <\/clipPath> <\/defs> <\/svg> ` #### Notes - `note.svg` - ` <\/g> <\/g> <\/g> <\/g> <\/g> <\/g> <\/svg> `