# Zortrax Endureal: specs, SimplyPrint compatibility and setup

> **Not expected to work** (Most likely not). We don't expect it to work, but we could be wrong.

- By Zortrax, Poland
- Launched September 2019
- Canonical page: https://simplyprint.io/compatibility/zortrax-endureal

## Zortrax Endureal at a glance

The Zortrax Endureal is a 3D printer by Zortrax with a 400 x 300 x 300 mm build volume.

- Build volume: 400 x 300 x 300 mm
- Enclosure: Fully enclosed
- Prints well: PLA, PETG, ABS & ASA, Nylon (PA), Polycarbonate (PC), Carbon-fiber & glass-filled, High-temperature (PEI, PEEK, PEKK)
- Built-in camera: Yes
- Connectivity: Wi-Fi, Ethernet, USB

## Connect the Zortrax Endureal to SimplyPrint

| Way of connecting | Status | What you need | Notes |
| :--- | :--- | :--- | :--- |
| SimplyPrint | Not expected to work |  |  |
| OctoPrint (Directly, over USB) | Not expected to work |  | Prints only Z-SUITE's own job files, sent over the network or from a USB stick; no USB serial printing. ([Source](https://zortrax.com/3d-printers/endureal/)) |
| Klipper (Moonraker) | Not compatible |  | Closed Zortrax firmware on an Android-based controller; no Klipper. ([Source](https://zortrax.com/3d-printers/endureal/)) |

## What slicer to use for the Zortrax Endureal

None of the slicers in SimplyPrint's cloud can slice for the Zortrax Endureal that we know of: it doesn't take standard G-code. Use the slicer its maker recommends.

- [PrusaSlicer](https://simplyprint.io/features/slicer/prusaslicer): No profile for the Zortrax Endureal · Runs in the SimplyPrint cloud
- [OrcaSlicer](https://simplyprint.io/features/slicer/orcaslicer): No profile for the Zortrax Endureal · Runs in the SimplyPrint cloud
- [BambuStudio](https://simplyprint.io/features/slicer/bambustudio): No profile for the Zortrax Endureal · Runs in the SimplyPrint cloud
- [ElegooSlicer](https://simplyprint.io/features/slicer/elegooslicer): No profile for the Zortrax Endureal · Runs in the SimplyPrint cloud
- [CrealityPrint](https://simplyprint.io/features/slicer/crealityprint): No profile for the Zortrax Endureal · Runs in the SimplyPrint cloud
- [Cura](https://simplyprint.io/features/slicer/cura): No profile for the Zortrax Endureal · Runs in the SimplyPrint cloud
- [Kiri:Moto](https://simplyprint.io/features/slicer/kirimoto): No profile for the Zortrax Endureal · Runs in the SimplyPrint cloud

We only list slicers you can use in the SimplyPrint cloud, so there may be others for the Zortrax Endureal.

## The app for the Zortrax Endureal

Zortrax's own app is [Zortrax inCloud](https://zortrax.com/3d-printers/m300-dual/).


## Zortrax Endureal specifications: bed size, print height and more

### Size

- Build volume: 400 x 300 x 300 mm
- Bed type: Rectangle
- Bed size: 400 x 300 mm
- Max print height: 300 mm

### Printing

- Enclosure: Fully enclosed
- Max extruder temperature: 480 °C
- Has heated bed: Yes
- Max bed temperature: 220 °C
- Heated chamber: Up to 200 °C
- Number of nozzles: 2
- Toolheads: 2
- Direct drive: No
- Probing tool / Auto Bed Leveling: Yes
- Filament width: 1.75 mm

### Multi-material

- Toolchanger or hotend changer: No
- IDEX (independent dual extruders): No

### Connecting

- Connectivity: Wi-Fi, Ethernet, USB
- Built-in camera: Yes
- Supports serial printing: No
- Shipped firmware: The maker's own

### Files and slicing

- Supported file formats: G-code (.gcode, .gco, .g)

### The printer

- Printer manufacturer / brand: Zortrax
- Printer model name: Endureal
- Made by a company from: Poland
- Launched: September 2019
- Still made: Yes

[Read more by the manufacturer](https://zortrax.com/3d-printers/endureal/)

## What filament can the Zortrax Endureal print?

Filament compatibility for the Zortrax Endureal: the materials Zortrax lists for it.

| Filament | Suitability | Notes |
| :--- | :--- | :--- |
| PLA | Great | The easiest filament to print. Works on almost any printer; a heated bed helps adhesion but is not required. |
| PETG | Great | Comfortably in range (PETG likes a ~230-250C hotend and a ~70-85C bed). |
| TPU & flexibles | With care | Possible, but a Bowden extruder makes flexibles harder - print slowly and prefer firmer (higher-shore) TPU. |
| ABS & ASA | Great | On the maker's list of materials for this printer. |
| Nylon (PA) | Good | Doable with care - dry the filament thoroughly, and an enclosure helps a lot. |
| Polycarbonate (PC) | Great | On the maker's list of materials for this printer. |
| Carbon-fiber & glass-filled | Great | On the maker's list of materials for this printer. |
| High-temperature (PEI, PEEK, PEKK) | Great | On the maker's list of materials for this printer. |

## Printers like the Zortrax Endureal that work with SimplyPrint

- [Voron Voron Trident](https://simplyprint.io/compatibility/voron-voron-trident): Compatible, 350 x 350 x 250 mm, Similar build volume · Also prints ABS & ASA, Nylon (PA), Polycarbonate (PC)
- [Vision Miner 22 IDEX](https://simplyprint.io/compatibility/vision-miner-22-idex): Compatible, 350 x 350 x 450 mm, Similar build volume · Also prints ABS & ASA, Nylon (PA), Polycarbonate (PC), Carbon-fiber & glass-filled, High-temperature (PEI, PEEK, PEKK)
- [Creality K1 Max](https://simplyprint.io/compatibility/creality-k1-max): Compatible, 300 x 300 x 300 mm, Similar build volume · Also prints ABS & ASA, Nylon (PA), Polycarbonate (PC)
- [Bambu Lab H2S Combo](https://simplyprint.io/compatibility/bambu-lab-h2s-combo): Verified by SimplyPrint, 340 x 320 x 340 mm, Similar build volume · Also prints ABS & ASA, Nylon (PA), Polycarbonate (PC), Carbon-fiber & glass-filled, High-temperature (PEI, PEEK, PEKK)

## Where to buy the Zortrax Endureal

- [Zortrax's global store](https://simplyprint.io/buy/8397) (Official store)

## Frequently asked questions

### Is the Zortrax Endureal compatible with SimplyPrint?

To our knowledge the Zortrax Endureal is not yet supported. SimplyPrint works with 130+ brands and 600+ models via OctoPrint, Klipper and built-in integrations - check the compatibility list for a supported printer.

### What slicer should I use for the Zortrax Endureal?

None of the slicers in SimplyPrint's cloud can slice for the Zortrax Endureal that we know of: it doesn't take standard G-code. Use the slicer its maker recommends.

### What filament can the Zortrax Endureal print?

Zortrax lists ABS & ASA, Polycarbonate (PC), High-temperature (PEI, PEEK, PEKK) and Carbon-fiber & glass-filled for the Endureal.

### What is the Zortrax Endureal's bed size and build volume?

The Zortrax Endureal has a 400 x 300 mm print bed and prints up to 300 mm tall, a build volume of about 400 x 300 x 300 mm. See the full specifications table above for bed type, temperatures and more.

### When did the Zortrax Endureal come out?

Zortrax launched the Endureal in September 2019.

### Where can I buy the Zortrax Endureal?

From Zortrax's own store, which has shops for everywhere else. The links on this page go to those stores; some are affiliate links, so we may earn a commission at no extra cost to you.

---

© 2026 SimplyPrint. All rights reserved. This page and the compatibility, specification and review data on it are compiled by SimplyPrint and may not be copied, scraped, reproduced or republished, in whole or in part, without prior written permission. Printer images are the property of their respective manufacturers and are shown for identification purposes only; SimplyPrint claims no ownership of them. Quoted reviews belong to their authors.