# Wanhao Duplicator i3 Plus Mark II: specs, SimplyPrint compatibility and setup

> **Expected to work** (Most likely). Not confirmed yet, but we expect it to work like the Wanhao Duplicator i3.

- By Wanhao, China
- Launched 2018
- Canonical page: https://simplyprint.io/compatibility/wanhao-duplicator-i3-plus-mark-ii

## Wanhao Duplicator i3 Plus Mark II at a glance

The Wanhao Duplicator i3 Plus Mark II is a 3D printer by Wanhao with a 200 x 200 x 180 mm build volume.

- Build volume: 200 x 200 x 180 mm
- Motion system: Bed slinger
- Prints well: PLA, PETG, TPU & flexibles
- Connectivity: USB, SD card

## Connect the Wanhao Duplicator i3 Plus Mark II to SimplyPrint

| Way of connecting | Status | What you need | Notes |
| :--- | :--- | :--- | :--- |
| SimplyPrint | Expected to work |  | Through OctoPrint |
| OctoPrint (Directly, over USB) | Expected to work | A Raspberry Pi running OctoPrint, plugged into the printer with a USB cable | i3-style printer that connects over USB (spec: 'USB, SD card'), like the Duplicator i3. ([Source](https://top3dshop.com/blog/wanhao-duplicator-i3-plus-mark-2-review)); Expected to work like the Wanhao Duplicator i3 |
| Klipper (Moonraker) | Not compatible |  | Doesn't ship Klipper. ([Source](https://top3dshop.com/blog/wanhao-duplicator-i3-plus-mark-2-review)); Doesn't ship with Klipper: it runs Klipper after you install it in place of its own firmware, a modification |

- [How to set up SimplyPrint on Wanhao Duplicator i3 Plus Mark II](https://simplyprint.io/setup-guide/wanhao/duplicator-i3-plus-mark-ii.md)
- [How to set up OctoPrint on Wanhao Duplicator i3 Plus Mark II](https://simplyprint.io/compatibility/wanhao-duplicator-i3-plus-mark-ii/octoprint-setup)

- [Help us confirm](https://simplyprint.io/compatibility/wanhao-duplicator-i3-plus-mark-ii/confirm)

### What works with SimplyPrint

Connected through OctoPrint, SimplyPrint is expected to support everything the Wanhao Duplicator i3 Plus Mark II lets other software do: the camera and AI failure detection, remote printing, temperature and movement control and AutoPrint. 3 features depend on how it's set up: the table says what each needs.

## What slicer to use for the Wanhao Duplicator i3 Plus Mark II

None of the slicers in SimplyPrint's cloud has a ready-made profile for the Wanhao Duplicator i3 Plus Mark II, but it takes standard G-code: start from a similar printer's profile and set the bed size, height and nozzle to match.

- [PrusaSlicer](https://simplyprint.io/features/slicer/prusaslicer): No profile for the Wanhao Duplicator i3 Plus Mark II · Runs in the SimplyPrint cloud
- [OrcaSlicer](https://simplyprint.io/features/slicer/orcaslicer): No profile for the Wanhao Duplicator i3 Plus Mark II · Runs in the SimplyPrint cloud
- [BambuStudio](https://simplyprint.io/features/slicer/bambustudio): No profile for the Wanhao Duplicator i3 Plus Mark II · Runs in the SimplyPrint cloud
- [ElegooSlicer](https://simplyprint.io/features/slicer/elegooslicer): No profile for the Wanhao Duplicator i3 Plus Mark II · Runs in the SimplyPrint cloud
- [CrealityPrint](https://simplyprint.io/features/slicer/crealityprint): No profile for the Wanhao Duplicator i3 Plus Mark II · Runs in the SimplyPrint cloud
- [Cura](https://simplyprint.io/features/slicer/cura): No profile for the Wanhao Duplicator i3 Plus Mark II · Runs in the SimplyPrint cloud
- [Kiri:Moto](https://simplyprint.io/features/slicer/kirimoto): No profile for the Wanhao Duplicator i3 Plus Mark II · Runs in the SimplyPrint cloud

We only list slicers you can use in the SimplyPrint cloud, so there may be others for the Wanhao Duplicator i3 Plus Mark II.

## The app for the Wanhao Duplicator i3 Plus Mark II

SimplyPrint works as the Wanhao Duplicator i3 Plus Mark II's app: on your phone and in any browser, with a slicer in the cloud.

- An app for iPhone and Android, the same in any browser, and a slicer in the cloud.
- More than monitoring: a print queue, AI failure detection, AutoPrint and accounts for a team.
- Printers from many brands in one place, side by side.
- Hosted in Frankfurt, Germany, under the GDPR.

[Connect the Wanhao Duplicator i3 Plus Mark II to SimplyPrint, free](https://simplyprint.io/setup-guide/wanhao/duplicator-i3-plus-mark-ii) · [App Store](https://apps.apple.com/app/simplyprint-3d/id1519749400) · [Google Play](https://play.google.com/store/apps/details?id=com.simplyprint.appdev)

## Automate the Wanhao Duplicator i3 Plus Mark II

**Bed slingers are the easiest to automate.** The Wanhao Duplicator i3 Plus Mark II moves its bed back and forth, so its plate comes out to the front of the printer. That's what plate swappers like these use: they take the finished plate off and slide a fresh one on. Without a kit, a G-code routine can push cooled prints off with the toolhead. For example: [JobOx](https://simplyprint.io/features/autoprint/jobox), [swapmod](https://simplyprint.io/features/autoprint/swapmod).

### Ways to automate it

- [Push prints off with the toolhead](https://simplyprint.io/features/autoprint/push-off): On a bed slinger, a G-code routine can sweep the cooled print off the bed before the next job starts.
- [Your own ejection G-code](https://simplyprint.io/features/autoprint/custom): Write the routine that clears your plate, and AutoPrint runs it after every print.
- [A robot arm, or anything with an API](https://simplyprint.io/features/autoprint/api): Tell SimplyPrint the plate is clear through the API or a webhook, from a robot arm or your own system.
- [Clear it by hand, keep the queue](https://simplyprint.io/features/autoprint/manual-mode): AutoPrint waits for you to mark the plate clear, then starts the next job.

[How AutoPrint works](https://simplyprint.io/features/autoprint). AutoPrint comes with the Pro plan and up.

## Wanhao Duplicator i3 Plus Mark II specifications: bed size, print height and more

### Size

- Build volume: 200 x 200 x 180 mm
- Bed type: Square
- Bed size: 200 x 200 mm
- Max print height: 180 mm

### Printing

- Motion system: Bed slinger
- Max extruder temperature: 260 °C
- Has heated bed: Yes
- Max bed temperature: 100 °C
- Number of nozzles: 1
- Toolheads: 1
- Direct drive: Yes
- Probing tool / Auto Bed Leveling: Yes
- Filament width: 1.75 mm

### Multi-material

- Toolchanger or hotend changer: No
- IDEX (independent dual extruders): No

### Connecting

- Connectivity: USB, SD card
- Supports serial printing: Unknown
- Shipped firmware: Unknown

### Files and slicing

- Supported file formats: G-code (.gcode, .gco, .g)

### The printer

- Printer manufacturer / brand: Wanhao
- Printer model name: Duplicator i3 Plus Mark II
- Made by a company from: China
- Launched: 2018

[Read more by the manufacturer](https://web.archive.org/web/20180612104622/http://www.wanhao3dprinter.com/Unboxin/ShowArticle.asp?ArticleID=78)

## What filament can the Wanhao Duplicator i3 Plus Mark II print?

Filament compatibility for the Wanhao Duplicator i3 Plus Mark II: the materials it can handle, judged from its hotend, bed, chamber and enclosure.

| Filament | Suitability | Notes |
| :--- | :--- | :--- |
| PLA | Great | The easiest filament to print. Works on almost any printer; a heated bed helps adhesion but is not required. |
| PETG | Great | Comfortably in range (PETG likes a ~230-250C hotend and a ~70-85C bed). |
| TPU & flexibles | Great | The direct-drive extruder feeds flexible filament well. Print slowly for clean results. |
| ABS & ASA | With care | The bed is hot enough, but ABS and ASA warp without an enclosure, which is strongly recommended for clean prints. |
| Nylon (PA) | With care | Possible with care - an enclosure and very dry filament are essential. |
| Polycarbonate (PC) | Not ideal | Not recommended - PC needs very high hotend temps and an enclosed chamber. |
| Carbon-fiber & glass-filled | With care | Possible if you fit a hardened or wear-resistant nozzle - the abrasive fibers quickly wear a stock brass nozzle. |

### Best filament for the Wanhao Duplicator i3 Plus Mark II

Filaments the Wanhao Duplicator i3 Plus Mark II prints well, Wanhao's own first, then the best known.

- [Bambu Lab PLA Basic](https://simplyprint.io/filaments/bambu-lab/pla-basic): PLA, 190-230 °C
- [Bambu Lab PLA Matte](https://simplyprint.io/filaments/bambu-lab/pla-matte): PLA, 190-230 °C
- [SUNLU PLA](https://simplyprint.io/filaments/sunlu/pla): PLA, 200-240 °C
- [Anycubic PETG](https://simplyprint.io/filaments/anycubic/petg): PETG, 230-250 °C
- [Anycubic PLA Basic](https://simplyprint.io/filaments/anycubic/pla-basic): PLA, 190-230 °C
- [Anycubic PLA Plus](https://simplyprint.io/filaments/anycubic/pla-plus): PLA, 190-230 °C
- [Bambu Lab PETG Basic](https://simplyprint.io/filaments/bambu-lab/petg-basic): PETG, 230-260 °C
- [Bambu Lab PETG HF](https://simplyprint.io/filaments/bambu-lab/petg-hf): PETG, 230-260 °C

## Compare the Wanhao Duplicator i3 Plus Mark II with similar printers

- [Wanhao D6 Plus](https://simplyprint.io/compatibility/wanhao-d6-plus): Compatible, 200 x 200 x 175 mm, Also by Wanhao · Similar build volume
- [Wanhao Duplicator 4S](https://simplyprint.io/compatibility/wanhao-duplicator-4s): Compatible, 225 x 145 x 150 mm, Also by Wanhao · Similar build volume
- [Bambu Lab A1 Mini](https://simplyprint.io/compatibility/bambu-lab-a1-mini): Verified by SimplyPrint, 180 x 180 x 180 mm, Similar build volume
- [Flashforge Adventurer 5M](https://simplyprint.io/compatibility/flashforge-adventurer-5m): Compatible, 220 x 220 x 220 mm, Similar build volume
- [Compare the Wanhao Duplicator i3 Plus Mark II with other printers](https://simplyprint.io/compatibility/compare?compare=wanhao-duplicator-i3-plus-mark-ii#choose)

Affiliate disclosure: Some links on this page are affiliate links. We may earn a commission if you make a purchase, at no extra cost to you. As an Amazon Associate, we earn from qualifying purchases.

## Frequently asked questions

### Is the Wanhao Duplicator i3 Plus Mark II compatible with SimplyPrint?

Most likely. We expect the Wanhao Duplicator i3 Plus Mark II to connect to SimplyPrint via OctoPrint, but nobody has confirmed it yet. If you have one, the setup guide shows within minutes whether it works, and your answer confirms it for everyone.

### How do I connect the Wanhao Duplicator i3 Plus Mark II to SimplyPrint?

Follow our step-by-step setup guide for the Wanhao Duplicator i3 Plus Mark II. It shows how to connect it via OctoPrint, what you need for each, and which to pick.

### What slicer should I use for the Wanhao Duplicator i3 Plus Mark II?

Cura, PrusaSlicer and OrcaSlicer all work with the Wanhao Duplicator i3 Plus Mark II, and you can run any of them in SimplyPrint's online browser slicer - no install needed, on any device.

### Can I use OrcaSlicer with the Wanhao Duplicator i3 Plus Mark II?

Yes, but OrcaSlicer has no built-in profile for the Wanhao Duplicator i3 Plus Mark II that we know of: start from a similar printer's profile and set the bed size, height and nozzle to match.

### What filament can the Wanhao Duplicator i3 Plus Mark II print?

Based on its specs (hotend up to 260C, heated bed up to 100C), the Wanhao Duplicator i3 Plus Mark II handles PLA, PETG, or TPU & flexibles well. See the full filament guide above for ABS, nylon, PC and composites.

### Does the Wanhao Duplicator i3 Plus Mark II work with OctoPrint or Klipper?

The Wanhao Duplicator i3 Plus Mark II works with OctoPrint, and SimplyPrint connects to it through them - so you get cloud access, a queue and camera monitoring on top.

### What is the Wanhao Duplicator i3 Plus Mark II's bed size and build volume?

The Wanhao Duplicator i3 Plus Mark II has a 200 x 200 mm print bed and prints up to 180 mm tall, a build volume of about 200 x 200 x 180 mm. See the full specifications table above for bed type, temperatures and more.

### When did the Wanhao Duplicator i3 Plus Mark II come out?

Wanhao launched the Duplicator i3 Plus Mark II in 2018.

### Can the Wanhao Duplicator i3 Plus Mark II eject prints automatically?

There's no kit for it that we support yet, but SimplyPrint's AutoPrint can push prints off with the toolhead, or run your own ejection G-code, and then start the next job from your queue.

---

© 2026 SimplyPrint. All rights reserved. This page and the compatibility, specification and review data on it are compiled by SimplyPrint and may not be copied, scraped, reproduced or republished, in whole or in part, without prior written permission. Printer images are the property of their respective manufacturers and are shown for identification purposes only; SimplyPrint claims no ownership of them. Quoted reviews belong to their authors.