# Tronxy D01 Plus: specs, SimplyPrint compatibility and setup > **Expected to work** (Most likely). Not confirmed yet, but we expect it to work like the Tronxy X5SA. - By Tronxy, China - Launched April 2021 - Canonical page: https://simplyprint.io/compatibility/tronxy-d01-plus ## Tronxy D01 Plus at a glance The Tronxy D01 Plus is a 3D printer by Tronxy with a 330 x 330 x 400 mm build volume. - Build volume: 330 x 330 x 400 mm - Max print speed: 150 mm/s - Motion system: CoreXY - Prints well: PLA, PETG, TPU & flexibles, ABS & ASA - Connectivity: USB, SD card ## Connect the Tronxy D01 Plus to SimplyPrint | Way of connecting | Status | What you need | Notes | | :--- | :--- | :--- | :--- | | SimplyPrint | Expected to work | | Through OctoPrint | | OctoPrint (Directly, over USB) | Expected to work | A Raspberry Pi running OctoPrint, plugged into the printer with a USB cable | Tronxy firmware (D01_PLUS build in Tronxy's Marlin-based F103 repo); the D01 manual lists SD card and USB cable. Like the X5SA. ([Source](https://tronxy3d.com/pages/d01-manual)); Expected to work like the Tronxy X5SA | | Klipper (Moonraker) | Not compatible | | Ships Marlin-based firmware; Klipper only after you install it. ([Source](https://github.com/tronxy3d/F103_PIC480x320)); Doesn't ship with Klipper: it runs Klipper after you install it in place of its own firmware, a modification | - [How to set up SimplyPrint on Tronxy D01 Plus](https://simplyprint.io/setup-guide/tronxy/d01-plus.md) - [How to set up OctoPrint on Tronxy D01 Plus](https://simplyprint.io/compatibility/tronxy-d01-plus/octoprint-setup) - [Help us confirm](https://simplyprint.io/compatibility/tronxy-d01-plus/confirm) ### What works with SimplyPrint Connected through OctoPrint, SimplyPrint is expected to support everything the Tronxy D01 Plus lets other software do: the camera and AI failure detection, remote printing, temperature and movement control and AutoPrint. 3 features depend on how it's set up: the table says what each needs. ## What slicer to use for the Tronxy D01 Plus None of the slicers in SimplyPrint's cloud has a ready-made profile for the Tronxy D01 Plus, but it takes standard G-code: start from a similar printer's profile and set the bed size, height and nozzle to match. - [PrusaSlicer](https://simplyprint.io/features/slicer/prusaslicer): No profile for the Tronxy D01 Plus · Runs in the SimplyPrint cloud - [OrcaSlicer](https://simplyprint.io/features/slicer/orcaslicer): No profile for the Tronxy D01 Plus · Runs in the SimplyPrint cloud - [BambuStudio](https://simplyprint.io/features/slicer/bambustudio): No profile for the Tronxy D01 Plus · Runs in the SimplyPrint cloud - [ElegooSlicer](https://simplyprint.io/features/slicer/elegooslicer): No profile for the Tronxy D01 Plus · Runs in the SimplyPrint cloud - [CrealityPrint](https://simplyprint.io/features/slicer/crealityprint): No profile for the Tronxy D01 Plus · Runs in the SimplyPrint cloud - [Cura](https://simplyprint.io/features/slicer/cura): No profile for the Tronxy D01 Plus · Runs in the SimplyPrint cloud - [Kiri:Moto](https://simplyprint.io/features/slicer/kirimoto): No profile for the Tronxy D01 Plus · Runs in the SimplyPrint cloud We only list slicers you can use in the SimplyPrint cloud, so there may be others for the Tronxy D01 Plus. ## The app for the Tronxy D01 Plus Tronxy doesn't make an app for the Tronxy D01 Plus. SimplyPrint works as its app: on your phone and in any browser, with a slicer in the cloud. - An app for iPhone and Android, the same in any browser, and a slicer in the cloud. - More than monitoring: a print queue, AI failure detection, AutoPrint and accounts for a team. - Printers from many brands in one place, side by side. - Hosted in Frankfurt, Germany, under the GDPR. [Connect the Tronxy D01 Plus to SimplyPrint, free](https://simplyprint.io/setup-guide/tronxy/d01-plus) · [App Store](https://apps.apple.com/app/simplyprint-3d/id1519749400) · [Google Play](https://play.google.com/store/apps/details?id=com.simplyprint.appdev) ## Automate the Tronxy D01 Plus **CoreXY printers push their prints off.** The Tronxy D01 Plus's bed only moves up and down, so the usual way to automate it is a G-code routine that lets the toolhead push the cooled print off the front of the plate before the next job starts. ### Ways to automate it - [Push prints off with the toolhead](https://simplyprint.io/features/autoprint/push-off): On a CoreXY printer, a G-code routine can push the cooled print off the front of the plate before the next job starts. - [Your own ejection G-code](https://simplyprint.io/features/autoprint/custom): Write the routine that clears your plate, and AutoPrint runs it after every print. - [A robot arm, or anything with an API](https://simplyprint.io/features/autoprint/api): Tell SimplyPrint the plate is clear through the API or a webhook, from a robot arm or your own system. - [Clear it by hand, keep the queue](https://simplyprint.io/features/autoprint/manual-mode): AutoPrint waits for you to mark the plate clear, then starts the next job. [How AutoPrint works](https://simplyprint.io/features/autoprint). AutoPrint comes with the Pro plan and up. ## Tronxy D01 Plus specifications: bed size, print height and more ### Size - Build volume: 330 x 330 x 400 mm - Bed type: Square - Bed size: 330 x 330 mm - Max print height: 400 mm ### Printing - Motion system: CoreXY - Max print speed: 150 mm/s - Max extruder temperature: 275 °C - Has heated bed: Yes - Max bed temperature: 100 °C - Number of nozzles: 1 - Toolheads: 1 - Direct drive: Yes - Probing tool / Auto Bed Leveling: Yes - Filament width: 1.75 mm ### Multi-material - Toolchanger or hotend changer: No - IDEX (independent dual extruders): No ### Connecting - Connectivity: USB, SD card - Prints from: microSD card - Supports serial printing: Unknown - Shipped firmware: Marlin ### Files and slicing - Supported file formats: G-code (.gcode, .gco, .g) ### The printer - Printer manufacturer / brand: Tronxy - Printer model name: D01 Plus - Made by a company from: China - Launched: April 2021 - Still made: Yes [Read more by the manufacturer](https://www.tronxy3d.com/products/d01-plus-v2-guard) ## What filament can the Tronxy D01 Plus print? Filament compatibility for the Tronxy D01 Plus: the materials Tronxy lists for it. | Filament | Suitability | Notes | | :--- | :--- | :--- | | PLA | Great | On the maker's list of materials for this printer. | | PETG | Great | On the maker's list of materials for this printer. | | TPU & flexibles | Great | On the maker's list of materials for this printer. | | ABS & ASA | Great | On the maker's list of materials for this printer. | | Nylon (PA) | With care | Possible with care - an enclosure and very dry filament are essential. | | Polycarbonate (PC) | With care | On the edge - PC really wants an enclosed, hot chamber to avoid warping. | | Carbon-fiber & glass-filled | With care | Possible if you fit a hardened or wear-resistant nozzle - the abrasive fibers quickly wear a stock brass nozzle. | ### Best filament for the Tronxy D01 Plus Filaments the Tronxy D01 Plus prints well, Tronxy's own first, then the best known. - [Bambu Lab PLA Basic](https://simplyprint.io/filaments/bambu-lab/pla-basic): PLA, 190-230 °C - [Bambu Lab PLA Matte](https://simplyprint.io/filaments/bambu-lab/pla-matte): PLA, 190-230 °C - [SUNLU PLA](https://simplyprint.io/filaments/sunlu/pla): PLA, 190-230 °C - [Anycubic PETG](https://simplyprint.io/filaments/anycubic/petg): PETG, 230-250 °C - [Anycubic PLA Basic](https://simplyprint.io/filaments/anycubic/pla-basic): PLA, 190-230 °C - [Anycubic PLA Plus](https://simplyprint.io/filaments/anycubic/pla-plus): PLA, 190-230 °C - [Bambu Lab PETG Basic](https://simplyprint.io/filaments/bambu-lab/petg-basic): PETG, 230-260 °C - [Bambu Lab PETG HF](https://simplyprint.io/filaments/bambu-lab/petg-hf): PETG, 230-260 °C ## Compare the Tronxy D01 Plus with similar printers - [Tronxy X5SA-400](https://simplyprint.io/compatibility/tronxy-x5sa-400): Expected to work, 400 x 400 x 400 mm, Also by Tronxy · Similar build volume · Also prints ABS & ASA - [Tronxy XY-3 Pro V2](https://simplyprint.io/compatibility/tronxy-xy-3-pro-v2): Expected to work, 300 x 300 x 400 mm, Also by Tronxy · Similar build volume · Also prints ABS & ASA - [Voron Voron Trident](https://simplyprint.io/compatibility/voron-voron-trident): Compatible, 350 x 350 x 250 mm, Similar build volume · Also prints ABS & ASA - [Vivedino Troodon 2.0](https://simplyprint.io/compatibility/vivedino-troodon-2-0): Compatible, 350 x 350 x 320 mm, Similar build volume · Also prints ABS & ASA - [Compare the Tronxy D01 Plus with other printers](https://simplyprint.io/compatibility/compare?compare=tronxy-d01-plus#choose) ## Where to buy the Tronxy D01 Plus - [Tronxy's global store](https://simplyprint.io/buy/8387) (Official store) ## About Tronxy Tronxy (Shenzhen Tronxy Technology Co., Ltd) is a Shenzhen 3D printer maker whose founder built the company's first printer in 2013. It sells low- and mid-priced FDM printers, from the X5SA and XY-3 series up to the very large VEHO line (1,000 mm and more), plus Moore clay printers, through its own store, Amazon, eBay, AliExpress, Alibaba and dealers. Buyers are hobbyists, schools and small businesses that want a large build volume for little money. - Headquarters: Shenzhen, China - Website: https://www.tronxy.com Openness: Open (4.3 of 5) Mostly open: Marlin source on GitHub, Klipper on the newer large printers, open filament and no cloud. Documentation is thin, and firmware downloads go through an email request. - Firmware and custom firmware (4 of 5): Tronxy publishes Marlin source for its STM32/GD32 boards on GitHub (tronxy3d) under GPL-3.0, covering nearly 30 X5SA, XY, D01 and VEHO 500-800 variants, last updated February 2024. Its newer VEHO PRO and A series ship with Klipper, and it sells a Klipper upgrade kit for the X5SA. - Local control and integrations (5 of 5): We found no Tronxy cloud service or account. The Klipper VEHO PRO prints from a USB flash drive or over a USB data cable, Wi-Fi or Ethernet, all on your own premises, and Tronxy publishes the Marlin source for its X5SA and XY printers, which host software such as OctoPrint drives over USB. - Third-party filament, slicers and parts (4 of 5): Open filament (1.75 mm, with 2.85 mm print heads for the VEHO) and standard G-code, which any slicer produces. VEHO hotends and print heads such as the Ext06 are Tronxy's own parts. - Repairs and spare parts (4 of 5): Tronxy's store sells model-specific mainboards, hotends, nozzles and extruder kits for current and older lines (X5SA, XY, VEHO), including Klipper-version parts. - Community and documentation (3 of 5): Firmware source and build steps are on GitHub, and upstream Klipper ships configs for eight Tronxy models. Tronxy's own download page asks owners to email for the right firmware instead of offering it directly. ### Pros - Very large build volumes for the price, up to 1,000 mm and more in the VEHO line. - Marlin source is public on GitHub, and the newer VEHO models run open-source Klipper. - No cloud or account: print over USB, memory card, Wi-Fi or Ethernet. - Spare mainboards, hotends and nozzles sold for current and older models. ### Cons - Firmware on Tronxy's website is by email request rather than a direct download. - Dozens of models and variants with similar names (the published firmware alone covers nearly 30), so check carefully which firmware and parts fit. - VEHO hotends and print heads are Tronxy-specific parts. ### Track record - October 2022: Tronxy began publishing Marlin source for its STM32F446/GD32-based boards on GitHub (tronxy3d) under GPL-3.0; it updated it until February 2024. - December 2020: Tronxy launched the XY-3 SE on Kickstarter; the company says shipping finished in April 2021. How Tronxy compares with every other brand: https://simplyprint.io/articles/best-3d-printer Affiliate disclosure: Some links on this page are affiliate links. We may earn a commission if you make a purchase, at no extra cost to you. As an Amazon Associate, we earn from qualifying purchases. ## Frequently asked questions ### Is the Tronxy D01 Plus compatible with SimplyPrint? Most likely. We expect the Tronxy D01 Plus to connect to SimplyPrint via OctoPrint, but nobody has confirmed it yet. If you have one, the setup guide shows within minutes whether it works, and your answer confirms it for everyone. ### How do I connect the Tronxy D01 Plus to SimplyPrint? Follow our step-by-step setup guide for the Tronxy D01 Plus. It shows how to connect it via OctoPrint, what you need for each, and which to pick. ### What slicer should I use for the Tronxy D01 Plus? Cura, PrusaSlicer and OrcaSlicer all work with the Tronxy D01 Plus, and you can run any of them in SimplyPrint's online browser slicer - no install needed, on any device. ### Can I use OrcaSlicer with the Tronxy D01 Plus? Yes, but OrcaSlicer has no built-in profile for the Tronxy D01 Plus that we know of: start from a similar printer's profile and set the bed size, height and nozzle to match. ### What filament can the Tronxy D01 Plus print? Tronxy lists PLA, ABS & ASA, PETG and TPU & flexibles for the D01 Plus. ### Does the Tronxy D01 Plus work with OctoPrint or Klipper? The Tronxy D01 Plus works with OctoPrint, and SimplyPrint connects to it through them - so you get cloud access, a queue and camera monitoring on top. ### What is the Tronxy D01 Plus's bed size and build volume? The Tronxy D01 Plus has a 330 x 330 mm print bed and prints up to 400 mm tall, a build volume of about 330 x 330 x 400 mm. See the full specifications table above for bed type, temperatures and more. ### When did the Tronxy D01 Plus come out? Tronxy launched the D01 Plus in April 2021. ### Can the Tronxy D01 Plus eject prints automatically? There's no kit for it that we support yet, but SimplyPrint's AutoPrint can push prints off with the toolhead, or run your own ejection G-code, and then start the next job from your queue. ### Where can I buy the Tronxy D01 Plus? From Tronxy's own store, which has shops for everywhere else. The links on this page go to those stores; some are affiliate links, so we may earn a commission at no extra cost to you. --- © 2026 SimplyPrint. All rights reserved. This page and the compatibility, specification and review data on it are compiled by SimplyPrint and may not be copied, scraped, reproduced or republished, in whole or in part, without prior written permission. Printer images are the property of their respective manufacturers and are shown for identification purposes only; SimplyPrint claims no ownership of them. Quoted reviews belong to their authors.