# InfiMech TX: specs, SimplyPrint compatibility and setup

> **Compatible** (We're sure). It's known to work with SimplyPrint, from documentation, the protocol or owners' prints.

- By InfiMech, China
- Launched September 2023
- Canonical page: https://simplyprint.io/compatibility/infimech-tx

## InfiMech TX at a glance

The InfiMech TX is a 3D printer by InfiMech with a 220 x 220 x 250 mm build volume.

- Build volume: 220 x 220 x 250 mm
- Enclosure: Fully enclosed
- Max print speed: 500 mm/s
- Motion system: CoreXY
- Prints well: PLA, PETG, TPU & flexibles, ABS & ASA, Nylon (PA), Polycarbonate (PC)
- Built-in camera: No

## Connect the InfiMech TX to SimplyPrint

| Way of connecting | Status | What you need | Notes |
| :--- | :--- | :--- | :--- |
| SimplyPrint | Compatible |  | Through Klipper (Moonraker) |
| Klipper (Moonraker) | Compatible | Nothing extra: the printer runs Klipper as it ships | Ships Klipper ('CoreXY Structure with Klipper Firmware') with Moonraker on port 7125 and Fluidd, LAN-reachable, no root step needed per the stock config backup. ([Source](https://infimech.com/products/infimech-tx-3d-printer-high-speed-printing)) |
| OctoPrint (Directly, over USB) | Not compatible |  | Ships Klipper; OctoPrint only on top of it. ([Source](https://infimech.com/products/infimech-tx-3d-printer-high-speed-printing)); Ships with Klipper: OctoPrint only runs on top of it, through the OctoKlipper plugin |

- [How to set up SimplyPrint on InfiMech TX](https://simplyprint.io/setup-guide/infimech/tx.md)
- [How to set up Mainsail on InfiMech TX](https://docs.mainsail.xyz/setup)
- [How to set up Fluidd on InfiMech TX](https://docs.fluidd.xyz/installation)

### What works with SimplyPrint

Connected through Klipper (Moonraker), SimplyPrint supports most of what it offers on the InfiMech TX: the camera and AI failure detection, remote printing, skipping objects, temperature and movement control and AutoPrint. Not yet in SimplyPrint through Klipper (Moonraker): download the file before the print starts.

## What slicer to use for the InfiMech TX

None of the slicers in SimplyPrint's cloud has a ready-made profile for the InfiMech TX, but it takes standard G-code: start from a similar printer's profile and set the bed size, height and nozzle to match.

- [PrusaSlicer](https://simplyprint.io/features/slicer/prusaslicer): No profile for the InfiMech TX · Runs in the SimplyPrint cloud
- [OrcaSlicer](https://simplyprint.io/features/slicer/orcaslicer): No profile for the InfiMech TX · Runs in the SimplyPrint cloud
- [BambuStudio](https://simplyprint.io/features/slicer/bambustudio): No profile for the InfiMech TX · Runs in the SimplyPrint cloud
- [ElegooSlicer](https://simplyprint.io/features/slicer/elegooslicer): No profile for the InfiMech TX · Runs in the SimplyPrint cloud
- [CrealityPrint](https://simplyprint.io/features/slicer/crealityprint): No profile for the InfiMech TX · Runs in the SimplyPrint cloud
- [Cura](https://simplyprint.io/features/slicer/cura): No profile for the InfiMech TX · Runs in the SimplyPrint cloud
- [Kiri:Moto](https://simplyprint.io/features/slicer/kirimoto): No profile for the InfiMech TX · Runs in the SimplyPrint cloud

We only list slicers you can use in the SimplyPrint cloud, so there may be others for the InfiMech TX.

## The app for the InfiMech TX

SimplyPrint works as the InfiMech TX's app: on your phone and in any browser, with a slicer in the cloud.

- An app for iPhone and Android, the same in any browser, and a slicer in the cloud.
- More than monitoring: a print queue, AI failure detection, AutoPrint and accounts for a team.
- Printers from many brands in one place, side by side.
- Hosted in Frankfurt, Germany, under the GDPR.

[Connect the InfiMech TX to SimplyPrint, free](https://simplyprint.io/setup-guide/infimech/tx) · [App Store](https://apps.apple.com/app/simplyprint-3d/id1519749400) · [Google Play](https://play.google.com/store/apps/details?id=com.simplyprint.appdev)

## Automate the InfiMech TX

**Enclosed printers push their prints out.** The InfiMech TX's bed only moves up and down inside its enclosure, so instead of swapping plates, a push-off routine lets the toolhead push the cooled print off the plate and out through its front door, which has to be open while it runs. Some printers won't print with the door open (the Prusa CORE One has a door sensor), so check yours first.

### Ways to automate it

- [Push prints off with the toolhead](https://simplyprint.io/features/autoprint/push-off): On a CoreXY printer, a G-code routine can push the cooled print off the front of the plate before the next job starts.
- [Your own ejection G-code](https://simplyprint.io/features/autoprint/custom): Write the routine that clears your plate, and AutoPrint runs it after every print.
- [A robot arm, or anything with an API](https://simplyprint.io/features/autoprint/api): Tell SimplyPrint the plate is clear through the API or a webhook, from a robot arm or your own system.
- [Clear it by hand, keep the queue](https://simplyprint.io/features/autoprint/manual-mode): AutoPrint waits for you to mark the plate clear, then starts the next job.

[How AutoPrint works](https://simplyprint.io/features/autoprint). AutoPrint comes with the Pro plan and up.

## InfiMech TX specifications: bed size, print height and more

### Size

- Build volume: 220 x 220 x 250 mm
- Bed type: Square
- Bed size: 220 x 220 mm
- Max print height: 250 mm

### Printing

- Enclosure: Fully enclosed
- Motion system: CoreXY
- Max print speed: 500 mm/s
- Max extruder temperature: 300 °C
- Has heated bed: Yes
- Max bed temperature: 120 °C
- Number of nozzles: 1
- Toolheads: 1
- Direct drive: Yes
- Probing tool / Auto Bed Leveling: Yes
- Filament width: 1.75 mm

### Multi-material

- Toolchanger or hotend changer: No
- IDEX (independent dual extruders): No

### Connecting

- Built-in camera: No
- Supports serial printing: No
- Shipped firmware: Klipper

### Files and slicing

- Supported file formats: G-code (.gcode, .gco, .g)

### The printer

- Printer manufacturer / brand: InfiMech
- Printer model name: TX
- Made by a company from: China
- Launched: September 2023
- Still made: Yes

[Read more by the manufacturer](https://infimech.com/products/infimech-tx-3d-printer-high-speed-printing)

## What filament can the InfiMech TX print?

Filament compatibility for the InfiMech TX: the materials it can handle, judged from its hotend, bed, chamber and enclosure.

| Filament | Suitability | Notes |
| :--- | :--- | :--- |
| PLA | Great | The easiest filament to print. Works on almost any printer; a heated bed helps adhesion but is not required. |
| PETG | Great | Comfortably in range (PETG likes a ~230-250C hotend and a ~70-85C bed). |
| TPU & flexibles | Great | The direct-drive extruder feeds flexible filament well. Print slowly for clean results. |
| ABS & ASA | Great | Enclosed, with a hot enough hotend and bed: ABS and ASA print well. |
| Nylon (PA) | Good | Doable with care - dry the filament thoroughly, and an enclosure helps a lot. |
| Polycarbonate (PC) | Good | In range for PC. Dry the filament, print slowly, and use an enclosure for the best results. |
| Carbon-fiber & glass-filled | With care | Possible if you fit a hardened or wear-resistant nozzle - the abrasive fibers quickly wear a stock brass nozzle. |

### Best filament for the InfiMech TX

Filaments the InfiMech TX prints well, InfiMech's own first, then the best known.

- [Bambu Lab PLA Basic](https://simplyprint.io/filaments/bambu-lab/pla-basic): PLA, 190-230 °C
- [Bambu Lab PLA Matte](https://simplyprint.io/filaments/bambu-lab/pla-matte): PLA, 190-230 °C
- [SUNLU PLA](https://simplyprint.io/filaments/sunlu/pla): PLA, 190-230 °C
- [Anycubic PETG](https://simplyprint.io/filaments/anycubic/petg): PETG, 230-250 °C
- [Anycubic PLA Basic](https://simplyprint.io/filaments/anycubic/pla-basic): PLA, 190-230 °C
- [Anycubic PLA Plus](https://simplyprint.io/filaments/anycubic/pla-plus): PLA, 190-230 °C
- [Bambu Lab PETG Basic](https://simplyprint.io/filaments/bambu-lab/petg-basic): PETG, 230-260 °C
- [Bambu Lab PETG HF](https://simplyprint.io/filaments/bambu-lab/petg-hf): PETG, 230-260 °C

## What reviewers say about the InfiMech TX

- [INFIMECH TX: A Cheap and Good Alternative to BambuLab X1C or P1S for $329](https://www.youtube.com/watch?v=eebpHHz1nns) (Aurora Tech, August 7, 2024): In-depth test of the enclosed CoreXY Klipper printer: fast, accurate (cleared his 0.05 mm tolerance test) and prints PLA through nylon carbon fibre with a 120 C bed at this price. Cons: auto Z offset set too low, conservative slicer profiles, awkward rear filament loading, small free eMMC and an outdated firmware update method.

## Compare the InfiMech TX with similar printers

- [Bambu Lab P1S](https://simplyprint.io/compatibility/bambu-lab-p1s): Verified by SimplyPrint, 256 x 256 x 256 mm, Similar build volume · Also prints ABS & ASA, Nylon (PA), Polycarbonate (PC)
- [Bambu Lab P2S Combo](https://simplyprint.io/compatibility/bambu-lab-p2s-combo): Verified by SimplyPrint, 256 x 256 x 256 mm, Similar build volume · Also prints ABS & ASA, Nylon (PA), Polycarbonate (PC)
- [Creality K1C](https://simplyprint.io/compatibility/creality-k1c): Compatible, 220 x 220 x 250 mm, Similar build volume · Also prints ABS & ASA, Nylon (PA), Polycarbonate (PC)
- [Creality K1](https://simplyprint.io/compatibility/creality-k1): Compatible, 220 x 220 x 250 mm, Similar build volume · Also prints ABS & ASA, Nylon (PA), Polycarbonate (PC)
- [Compare the InfiMech TX with other printers](https://simplyprint.io/compatibility/compare?compare=infimech-tx#choose)

## Where to buy the InfiMech TX

- [InfiMech's global store](https://simplyprint.io/buy/8313) (Official store)

Affiliate disclosure: Some links on this page are affiliate links. We may earn a commission if you make a purchase, at no extra cost to you. As an Amazon Associate, we earn from qualifying purchases.

## Frequently asked questions

### Is the InfiMech TX compatible with SimplyPrint?

Yes. You can connect the InfiMech TX to SimplyPrint via Klipper (Moonraker), then slice, queue, start and monitor prints from your browser or the mobile app.

### How do I connect the InfiMech TX to SimplyPrint?

Follow our step-by-step setup guide for the InfiMech TX. It shows how to connect it via Klipper (Moonraker), what you need for each, and which to pick.

### What slicer should I use for the InfiMech TX?

Cura, PrusaSlicer and OrcaSlicer all work with the InfiMech TX, and you can run any of them in SimplyPrint's online browser slicer - no install needed, on any device.

### Can I use OrcaSlicer with the InfiMech TX?

Yes, but OrcaSlicer has no built-in profile for the InfiMech TX that we know of: start from a similar printer's profile and set the bed size, height and nozzle to match.

### What filament can the InfiMech TX print?

Based on its specs (hotend up to 300C, heated bed up to 120C), the InfiMech TX handles PLA, PETG, TPU & flexibles, or ABS & ASA well. See the full filament guide above for ABS, nylon, PC and composites.

### Does the InfiMech TX work with OctoPrint or Klipper?

The InfiMech TX works with Klipper (Mainsail and Fluidd), and SimplyPrint connects to it through them - so you get cloud access, a queue and camera monitoring on top.

### What is the InfiMech TX's bed size and build volume?

The InfiMech TX has a 220 x 220 mm print bed and prints up to 250 mm tall, a build volume of about 220 x 220 x 250 mm. See the full specifications table above for bed type, temperatures and more.

### When did the InfiMech TX come out?

InfiMech launched the TX in September 2023.

### Can the InfiMech TX eject prints automatically?

There's no kit for it that we support yet, but SimplyPrint's AutoPrint can push prints off with the toolhead, or run your own ejection G-code, and then start the next job from your queue.

### Where can I buy the InfiMech TX?

From InfiMech's own store, which has shops for everywhere else. The links on this page go to those stores; some are affiliate links, so we may earn a commission at no extra cost to you.

---

© 2026 SimplyPrint. All rights reserved. This page and the compatibility, specification and review data on it are compiled by SimplyPrint and may not be copied, scraped, reproduced or republished, in whole or in part, without prior written permission. Printer images are the property of their respective manufacturers and are shown for identification purposes only; SimplyPrint claims no ownership of them. Quoted reviews belong to their authors.