# Afinia H: specs, SimplyPrint compatibility and setup

> **Compatible** (We're sure). It's known to work with SimplyPrint, from documentation, the protocol or owners' prints. In use with SimplyPrint.

- By Afinia, USA
- Canonical page: https://simplyprint.io/compatibility/afinia-h

## Afinia H at a glance

The Afinia H is a 3D printer by Afinia with a 255 x 225 x 205 mm build volume.

- Build volume: 255 x 225 x 205 mm
- Prints well: PLA, PETG

## Connect the Afinia H to SimplyPrint

| Way of connecting | Status | What you need | Notes |
| :--- | :--- | :--- | :--- |
| SimplyPrint | Compatible |  | Through OctoPrint |
| OctoPrint (Directly, over USB) | Compatible | A Raspberry Pi running OctoPrint, plugged into the printer with a USB cable | In use with SimplyPrint |
| Klipper (Moonraker) | Not compatible |  | Doesn't ship with Klipper: it runs Klipper after you install it in place of its own firmware, a modification |

- [How to set up SimplyPrint on Afinia H](https://simplyprint.io/setup-guide/afinia/h.md)
- [How to set up OctoPrint on Afinia H](https://simplyprint.io/compatibility/afinia-h/octoprint-setup)

### What works with SimplyPrint

Connected through OctoPrint, SimplyPrint supports everything the Afinia H lets other software do: the camera and AI failure detection, remote printing, temperature and movement control and AutoPrint. 3 features depend on how it's set up: the table says what each needs.

## What slicer to use for the Afinia H

None of the slicers in SimplyPrint's cloud has a ready-made profile for the Afinia H, but it takes standard G-code: start from a similar printer's profile and set the bed size, height and nozzle to match.

- [PrusaSlicer](https://simplyprint.io/features/slicer/prusaslicer): No profile for the Afinia H · Runs in the SimplyPrint cloud
- [OrcaSlicer](https://simplyprint.io/features/slicer/orcaslicer): No profile for the Afinia H · Runs in the SimplyPrint cloud
- [BambuStudio](https://simplyprint.io/features/slicer/bambustudio): No profile for the Afinia H · Runs in the SimplyPrint cloud
- [ElegooSlicer](https://simplyprint.io/features/slicer/elegooslicer): No profile for the Afinia H · Runs in the SimplyPrint cloud
- [CrealityPrint](https://simplyprint.io/features/slicer/crealityprint): No profile for the Afinia H · Runs in the SimplyPrint cloud
- [Cura](https://simplyprint.io/features/slicer/cura): No profile for the Afinia H · Runs in the SimplyPrint cloud
- [Kiri:Moto](https://simplyprint.io/features/slicer/kirimoto): No profile for the Afinia H · Runs in the SimplyPrint cloud

We only list slicers you can use in the SimplyPrint cloud, so there may be others for the Afinia H.

## The app for the Afinia H

SimplyPrint works as the Afinia H's app: on your phone and in any browser, with a slicer in the cloud.

- An app for iPhone and Android, the same in any browser, and a slicer in the cloud.
- More than monitoring: a print queue, AI failure detection, AutoPrint and accounts for a team.
- Printers from many brands in one place, side by side.
- Hosted in Frankfurt, Germany, under the GDPR.

[Connect the Afinia H to SimplyPrint, free](https://simplyprint.io/setup-guide/afinia/h) · [App Store](https://apps.apple.com/app/simplyprint-3d/id1519749400) · [Google Play](https://play.google.com/store/apps/details?id=com.simplyprint.appdev)

## Automate the Afinia H

### Ways to automate it

- [Your own ejection G-code](https://simplyprint.io/features/autoprint/custom): Write the routine that clears your plate, and AutoPrint runs it after every print.
- [A robot arm, or anything with an API](https://simplyprint.io/features/autoprint/api): Tell SimplyPrint the plate is clear through the API or a webhook, from a robot arm or your own system.
- [Clear it by hand, keep the queue](https://simplyprint.io/features/autoprint/manual-mode): AutoPrint waits for you to mark the plate clear, then starts the next job.

[How AutoPrint works](https://simplyprint.io/features/autoprint). AutoPrint comes with the Pro plan and up.

## Afinia H specifications: bed size, print height and more

### Size

- Build volume: 255 x 225 x 205 mm
- Bed type: Rectangle
- Bed size: 255 x 225 mm
- Max print height: 205 mm

### Printing

- Max extruder temperature: 280 °C
- Has heated bed: Yes
- Max bed temperature: 100 °C
- Number of nozzles: 1
- Direct drive: No
- Probing tool / Auto Bed Leveling: Yes
- Filament width: 1.75 mm

### Connecting

- Supports serial printing: Yes
- Shipped firmware: Marlin

### Files and slicing

- Supported file formats: G-code (.gcode, .gco, .g)

### The printer

- Printer manufacturer / brand: Afinia
- Printer model name: H
- Made by a company from: USA

## What filament can the Afinia H print?

Filament compatibility for the Afinia H: the materials it can handle, judged from its hotend, bed, chamber and enclosure.

| Filament | Suitability | Notes |
| :--- | :--- | :--- |
| PLA | Great | The easiest filament to print. Works on almost any printer; a heated bed helps adhesion but is not required. |
| PETG | Great | Comfortably in range (PETG likes a ~230-250C hotend and a ~70-85C bed). |
| TPU & flexibles | With care | Possible, but a Bowden extruder makes flexibles harder - print slowly and prefer firmer (higher-shore) TPU. |
| ABS & ASA | With care | The bed is hot enough, but ABS and ASA warp without an enclosure, which is strongly recommended for clean prints. |
| Nylon (PA) | With care | Possible with care - an enclosure and very dry filament are essential. |
| Polycarbonate (PC) | With care | On the edge - PC really wants an enclosed, hot chamber to avoid warping. |
| Carbon-fiber & glass-filled | With care | Possible if you fit a hardened or wear-resistant nozzle - the abrasive fibers quickly wear a stock brass nozzle. |

### Best filament for the Afinia H

Filaments the Afinia H prints well, Afinia's own first, then the best known.

- [Bambu Lab PLA Basic](https://simplyprint.io/filaments/bambu-lab/pla-basic): PLA, 190-230 °C
- [Bambu Lab PLA Matte](https://simplyprint.io/filaments/bambu-lab/pla-matte): PLA, 190-230 °C
- [SUNLU PLA](https://simplyprint.io/filaments/sunlu/pla): PLA, 200-240 °C
- [Anycubic PETG](https://simplyprint.io/filaments/anycubic/petg): PETG, 230-250 °C
- [Anycubic PLA Basic](https://simplyprint.io/filaments/anycubic/pla-basic): PLA, 190-230 °C
- [Anycubic PLA Plus](https://simplyprint.io/filaments/anycubic/pla-plus): PLA, 190-230 °C
- [Bambu Lab PETG Basic](https://simplyprint.io/filaments/bambu-lab/petg-basic): PETG, 230-260 °C
- [Bambu Lab PETG HF](https://simplyprint.io/filaments/bambu-lab/petg-hf): PETG, 230-260 °C

## Compare the Afinia H with similar printers

- [Afinia QD330](https://simplyprint.io/compatibility/afinia-qd330): Expected to work, 220 x 220 x 220 mm, Also by Afinia · Similar build volume
- [Bambu Lab P1S](https://simplyprint.io/compatibility/bambu-lab-p1s): Verified by SimplyPrint, 256 x 256 x 256 mm, Similar build volume
- [Bambu Lab A1](https://simplyprint.io/compatibility/bambu-lab-a1): Verified by SimplyPrint, 256 x 256 x 256 mm, Similar build volume
- [Creality Ender-3 V3 SE](https://simplyprint.io/compatibility/creality-ender-3-v3-se): Compatible, 220 x 220 x 250 mm, Similar build volume
- [Compare the Afinia H with other printers](https://simplyprint.io/compatibility/compare?compare=afinia-h#choose)

Affiliate disclosure: Some links on this page are affiliate links. We may earn a commission if you make a purchase, at no extra cost to you. As an Amazon Associate, we earn from qualifying purchases.

## Frequently asked questions

### Is the Afinia H compatible with SimplyPrint?

Yes. You can connect the Afinia H to SimplyPrint via OctoPrint, then slice, queue, start and monitor prints from your browser or the mobile app.

### How do I connect the Afinia H to SimplyPrint?

Follow our step-by-step setup guide for the Afinia H. It shows how to connect it via OctoPrint, what you need for each, and which to pick.

### What slicer should I use for the Afinia H?

Cura, PrusaSlicer and OrcaSlicer all work with the Afinia H, and you can run any of them in SimplyPrint's online browser slicer - no install needed, on any device.

### Can I use OrcaSlicer with the Afinia H?

Yes, but OrcaSlicer has no built-in profile for the Afinia H that we know of: start from a similar printer's profile and set the bed size, height and nozzle to match.

### What filament can the Afinia H print?

Based on its specs (hotend up to 280C, heated bed up to 100C), the Afinia H handles PLA or PETG well. See the full filament guide above for ABS, nylon, PC and composites.

### Does the Afinia H work with OctoPrint or Klipper?

The Afinia H works with OctoPrint, and SimplyPrint connects to it through them - so you get cloud access, a queue and camera monitoring on top.

### What is the Afinia H's bed size and build volume?

The Afinia H has a 255 x 225 mm print bed and prints up to 205 mm tall, a build volume of about 255 x 225 x 205 mm. See the full specifications table above for bed type, temperatures and more.

### Can the Afinia H eject prints automatically?

There's no kit for it that we support yet, but SimplyPrint's AutoPrint can run your own ejection G-code, work with a robot arm through the API, or wait for you to clear the plate, and then start the next job from your queue.

---

© 2026 SimplyPrint. All rights reserved. This page and the compatibility, specification and review data on it are compiled by SimplyPrint and may not be copied, scraped, reproduced or republished, in whole or in part, without prior written permission. Printer images are the property of their respective manufacturers and are shown for identification purposes only; SimplyPrint claims no ownership of them. Quoted reviews belong to their authors.